Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact AD9850 DDS module that generates sine and square waves from 0 to 40MHz with dual outputs and a 70MHz low-pass filter. Jumper-selectable serial or parallel control and an adjustable duty cycle make it a handy bench signal source.

Key Highlights

  • AD9850 DDS chip with 0-40MHz operating frequency range
  • Two sine wave and two square wave outputs on one board
  • 70MHz low-pass filter for cleaner waveform signal-to-noise
  • Jumper-selectable parallel or serial data input
  • Variable resistor adjusts square wave duty cycle
  • Compact 50 x 30mm board weighing about 4g

Ideal For

  • Electronics hobbyists building bench test setups
  • Students learning about DDS and waveform generation
  • Repair technicians needing a compact signal source
  • Makers prototyping audio and RF circuits
  • Educators demonstrating signal generation in class

Buying Tip

Check the supply voltage and control interface of your own setup before powering the module, since neither is specified in the listing and nothing else is included in the box.

Elecvora expert review

Our verdict

A genuinely useful little board for the price, best treated as a low-frequency bench helper rather than a precision lab generator. It delivers dual outputs, selectable control modes and a low-pass filter in a package small enough to leave on the bench.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Dual sine and square wave outputs
  • Jumper-selectable serial or parallel control
  • 70MHz low-pass filter improves waveform quality
  • Very small and light for breadboard use
  • Adjustable square wave duty cycle

Cons

  • Waveform quality degrades above roughly 20-30MHz
  • Square wave output limited to 0-1MHz
  • No controller, cable or power supply included

Best for

Hobbyists and technicians who need a compact, low-cost signal source for bench testing

Not ideal for

Precision RF measurement work requiring clean output at the top of the range

Specifications

Item TypeSignal Generator
Model No. / NameAD9850
Operating Frequency (MHz)0 - 40MHz
Continuous Discharge Current (A)0.005 Digital Output
Output Current (A)0.03 DAC
Storage Temperature (°C)-40 to 80
Operating Temperature (°C)-40 to 85
Length (mm)50
Width (mm)30
Weight (g)4
Shipping Weight0.005 kg
Shipping Dimensions4 × 3 × 1 cm

What's in the box

  • 1 x AD9850 DDS Signal Generator Module

Frequently Asked Questions

What frequency range does this module cover?
The AD9850 module operates from 0 to 40MHz. Square wave output is quoted at 0-1MHz, and waveform quality drops above roughly 20-30MHz.
How many outputs does the board have?
It provides two sine wave outputs and two square wave outputs.
How is the module controlled?
A jumper lets you select either parallel or serial data input, so it can be driven by a microcontroller or another digital source.
Can I change the square wave duty cycle?
Yes. The comparator reference input voltage is set by a variable resistor, and adjusting it changes the duty cycle of the square wave.
What is included in the package?
The package contains one AD9850 DDS Signal Generator Module. No controller, cable or power supply is included.
What are the operating temperature limits?
The module is rated for -40 to 85 degrees Celsius during operation and -40 to 80 degrees Celsius in storage.

Overview

The AD9850 DDS Signal Generator Module is a small direct digital synthesis board for anyone who needs a simple, affordable waveform source on the bench. It uses the AD9850 chip paired with a 125MHz active crystal, giving an operating frequency range of 0 to 40MHz. The board provides two sine wave outputs and two square wave outputs, so you can feed more than one point in a circuit from a single module.

Key Features

  • Dual waveform outputs: two sine and two square wave outputs are available from the board.
  • 70MHz low-pass filter: fitted to improve the signal-to-noise ratio of the generated waveform.
  • Selectable data input: a jumper lets you choose between parallel and serial data input modes.
  • Adjustable duty cycle: the comparator reference input voltage is set by a variable resistor, so turning it changes the square wave duty cycle.
  • DA reference pin brought out: pin 12 is led out so you can experiment with adjusting output waveform amplitude.
  • Compact size: approximately 50mm long, 30mm wide and around 4g in weight.

Specifications Explained

The 0-40MHz operating range covers audio through to low VHF work. Square wave output is quoted at 0-1MHz, so treat the square wave section as a lower-frequency tool. Output current is 0.03A for the DAC and 0.005A for the digital output, which tells you the board is intended to drive signal inputs rather than power loads.

Harmonic content grows noticeably above roughly 20-30MHz, and the waveform becomes less clean as frequency rises. The onboard 70MHz low-pass filter helps keep the output tidier, but expect the best waveform quality at lower frequencies. The module is rated for operation from -40 to 85 degrees Celsius and storage from -40 to 80 degrees Celsius.

Compatibility and Requirements

The board accepts either parallel or serial data input, selected by jumper, so it can be driven by a microcontroller or other digital control source. No controller, cable or power supply is included, and the listing does not specify a supply voltage, so check your own setup before connecting power. Plan for a stable supply and short, tidy wiring to keep the output clean.

Typical Uses

  • Bench testing filters, amplifiers and audio circuits
  • Signal injection during fault finding and repair
  • Learning about DDS synthesis and waveform generation
  • Breadboard experiments needing a compact signal source
  • Educational and hobby electronics projects

What's in the Box

One AD9850 DDS Signal Generator Module. Controller boards, cables and power supplies are not included.

Quick specs

Item Type
Signal Generator
Model No. / Name
AD9850
Operating Frequency (MHz)
0 - 40MHz
Continuous Discharge Current (A)
0.005 Digital Output
Output Current (A)
0.03 DAC
Storage Temperature (°C)
-40 to 80
See all specifications