Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by Adafruit, this breakout board is a good fit for makers, students and electronics hobbyists. Main specs: operating voltage (v) 3.3 to 5; resistance (ohm) 0-10K; interface type I2C. Check that your power source supplies 3.3 to 5 before connecting it.

Key Highlights

  • Operating Voltage (V): 3.3 to 5
  • Resistance (Ohm): 0-10K
  • Interface Type: I2C

Ideal For

  • Arduino, ESP32 and Raspberry Pi projects
  • School and college lab work
  • Prototypes and test rigs

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Operating Voltage (V)3.3 to 5
Resistance (Ohm)0-10K
Interface TypeI2C
Voltage Rating4.5V to 15.5V (analog)
Length (mm)25.4
Width (mm)17.7
Weight (g)1.6
Shipping Weight0.005 kg
Shipping Dimensions3 × 2 × 1 cm

Overview

The Adafruit DS3502 I2C Digital 10K Potentiometer Breakout - STEMMA QT/Qwiic, made by Adafruit, is listed in our breakout board range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Operating Voltage (V): 3.3 to 5 (match this to your power supply; too high a voltage can damage the part)
  • Resistance (Ohm): 0-10K
  • Interface Type: I2C (confirm your cable or board uses the same connector)
  • Voltage Rating: 4.5V to 15.5V (analog) (match this to your power supply; too high a voltage can damage the part)
  • Length (mm): 25.4 (measure your mounting space before ordering)
  • Width (mm): 17.7 (measure your mounting space before ordering)
  • Weight (g): 1.6 (important for drones, RC models and anything you carry)
  • Shipping Weight: 0.005 kg (important for drones, RC models and anything you carry)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

The DS3502 I2C Digital Potentiometer allows you to let your microcontroller adjust the resistance for you! Talking over an I2C bus, your Arduino, CircuitPython board,  or Python-powered computer can talk to the DS3502 and tell it to vary its resistance at your back and call. Working with the DS3502 is easy as an I2C controllable pie. We've put it on a breakout PCB with the required support circuitry and SparkFun qwiic compatible STEMMA QT connectors to allow you to use it with other similarly equipped boards without needing to solder. This handy little helper can work with 3.3V or 5V micros, so it's ready to get to work with a range of development boards. The DS3502 is a simple chip that does one thing well and so it's very easy to work with. Wire it up and set the value for the wiper, that's it. To make things even easier we've gone and written Arduino and CircuitPython/Python 3 drivers to simplify interfacing with your new knob-replacing friend. The wiper value is a 7-bit number meaning there are 128 possible levels of resistance to choose from 0-10K ohms. You can even set a default value that will be set on power-up. The analog voltage-controlled can be from 4.5-15.5V. Additionally, you can use the address jumpers or pins to set the I2C address to one of four values, allowing you to have four DS3502s on the same I2C bus.

Features:

  1. Allows microcontrollers to adjust the resistance
  2. Communicates via I2C bus
  3. Allow similarly equipped boards to connect to the potentiometer without any need to solder them
  4. 7-bit wiper value with 128 possible levels of resistance
  5. 0Ω to 10kΩ resistance range

Package Includes:

1 x Adafruit DS3502 I2C Digital 10K Potentiometer Breakout - STEMMA QT/Qwiic

Quick specs

Operating Voltage (V)
3.3 to 5
Resistance (Ohm)
0-10K
Interface Type
I2C
Voltage Rating
4.5V to 15.5V (analog)
Length (mm)
25.4
Width (mm)
17.7
See all specifications