Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by Adafruit, this led module is a good fit for makers, students and electronics hobbyists. Main specs: item type LED Board; voltage rating (v) 3-5; measurement range 10+Meters. Check that your power source supplies 3-5 before connecting it.

Key Highlights

  • Item Type: LED Board
  • Voltage Rating (V): 3-5
  • Measurement Range: 10+Meters

Ideal For

  • Arduino, ESP32 and Raspberry Pi projects
  • School and college lab work
  • Prototypes and test rigs

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Item TypeLED Board
Voltage Rating (V)3-5
Measurement Range10+Meters
DriverN-channel FET
Connector Type1× 3-pin JST PH, 1× 0.1" header
Current (mA)~200
Length (mm)25.4
Width (mm)17.7
Weight (g)1.8
Shipping Weight0.012 kg
Shipping Dimensions5 × 3 × 2 cm

Overview

The Adafruit High Power Infrared IR LED Emitter - STEMMA JST PH 2mm, made by Adafruit, is listed in our led module range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Item Type: LED Board
  • Voltage Rating (V): 3-5 (match this to your power supply; too high a voltage can damage the part)
  • Measurement Range: 10+Meters (quoted range is usually line-of-sight; walls and interference shorten it)
  • Driver: N-channel FET
  • Connector Type: 1× 3-pin JST PH, 1× 0.1" header (confirm your cable or board uses the same connector)
  • Current (mA): ~200 (your supply must deliver at least this much current)
  • Length (mm): 25.4 (measure your mounting space before ordering)
  • Width (mm): 17.7 (measure your mounting space before ordering)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

Adafruit High Power Infrared IR LED Emitter board is like a little ray gun for infrared light, with two high powered LED outputs. When controlled with the onboard N-Channel FET driver, you'll be blasting 100mA-200mA of current pulsing through each LED for 10+ meters of range! This is the easiest way to get great IR emitter range without wiring up a bunch of parts.

This board features a power transistor so you just need to provide about 3-5V DC power to the V+ power in, ground for ground, and then a 3-5V logic level signal on the input pin. When the pin is high, the LEDs are on, when the signal pin is low, the LEDs are off. Since humans don't see in IR, there's a red LED that will let you know when the IR LEDs are lit. Two LEDs are pre-soldered to the PCB, one pointing up and one pointing out. If you want even MORE coverage, there's a spot to solder in a separate 5mm IR LED (not included).


Features:

  1. Powers via 5V or 3V input.
  2. At 5V, draws approximately 200mA per LED (up to 400mA total when pulsing).
  3. At 3V, draws approximately 100mA per LED (up to 200mA total).
  4. Not intended for continuous illumination—best suited for short bursts like IR remote control transmission.
  5. Includes a fully assembled and tested PCB.
  6. No soldering required for basic use.
  7. Requires a 2mm pitch, 3-pin STEMMA JST PH cable (not included).
  8. Optional 0.1" header available for manual power/ground/signal soldering.

Package Includes:

1 x Adafruit High Power Infrared IR LED Emitter

Quick specs

Item Type
LED Board
Voltage Rating (V)
3-5
Measurement Range
10+Meters
Driver
N-channel FET
Connector Type
1× 3-pin JST PH, 1× 0.1" header
Current (mA)
~200
See all specifications