
1 / 3 · Click to enlarge
AI Summary
A refurbished dual channel Cytron SmartDriveDuo-60 motor driver delivering 60A continuous and 100A peak per channel from a 10V to 45V supply. It accepts PWM, UART, analog and RC servo control, with a cooling fan and thermal and overcurrent protection built in.
Key Highlights
- Dual channel driver with 60A continuous and 100A peak per channel
- Wide 10V to 45V operating range suits 3-cell and 6-cell LiPo packs
- Four control modes: PWM, UART, analog and RC servo signal
- Onboard brushless cooling fan plus temperature sensor
- Overcurrent and thermal protection with LED status indicators
- Professionally refurbished and fully tested before dispatch
Ideal For
- Combat robot builders needing high current per drive side
- Sumo robot teams using dual DC brushed motors
- RC hobbyists building mix-mode controlled robots
- Makers using Arduino or PIC for PWM or UART motor control
- Robotics students working with 10V to 45V battery packs
Buying Tip
Check that your motor stall current and battery voltage stay within 60A continuous per channel and the 10V to 45V input range, and wire polarity correctly since the board has no polarity protection.
Elecvora expert review
Our verdict
A capable dual channel driver for high-current robot builds, with genuinely useful control flexibility and built-in thermal and overcurrent protection. The refurbished condition keeps it practical for builders who want this current rating without paying new-unit pricing.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- 60A continuous and 100A peak per channel
- Four selectable control modes including RC and UART
- Fan cooling plus staged thermal current limiting
- Wide 10V to 45V input range
- Enclosed top and bottom covers with status LEDs
Cons
- No polarity protection, so wiring mistakes can damage the board
- Refurbished unit with opened packaging rather than new stock
- Requires adequate wire gauge and careful current planning
Best for
High-current dual-motor robot and RC vehicle builds
Not ideal for
Beginners wanting a plug-and-play, polarity-protected driver
Specifications
| Model Series | MDDS Series |
|---|---|
| Voltage Rating (V) | 10 to 45 |
| Current Rating (A) | 60 to 100 |
| Operating Voltage (VDC) | 10V to 45V |
| Peak Current (A) | 100 |
| Continuous Discharge Current (A) | 60 |
| Operating Mode | PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: Yes Analog: Yes, RC Servo Signal: Yes |
| No. of Channels | 2 |
| Battery Protect. Mode (Y/N) | Yes |
| Cooling Fan | Yes |
| LED Indicator | Yes |
| Polarity Protection (Y/N) | NO |
| Dimensions (L x W x H) mm | 190 x 121 x 45 |
| Overcurrent Protect. (Y/N) | Yes |
| Thermal Protection (Y/N) | Yes |
| Weight (g) | 400 |
| Shipping Weight | 0.45 kg |
| Shipping Dimensions | 20 × 13 × 5 cm |
Frequently Asked Questions
What does refurbished mean for this unit?
What voltage can I use?
How do I control the motors?
How much current can each channel handle?
Does it protect against overheating?
Is reverse polarity protected?
Overview
The Cytron SmartDriveDuo-60 MDDS60 is a two-channel smart motor driver for projects that need serious current. Each channel is rated at 60A continuous with a 100A peak, and the board runs from a 10V to 45V DC supply. That range covers common robot battery packs, including 3-cell and 6-cell LiPo configurations, and allows higher-voltage builds without a separate logic supply for the driver.
This listing is for a refurbished unit. The packaging was opened for testing, the board has been professionally refurbished by the Elecvora team, and it is fully tested and in proper working condition.
Key Features
- Dual channel output: drive two motors independently with 60A continuous and 100A peak per channel.
- Flexible control: PWM (lock-antiphase and sign-magnitude), UART, analog and RC servo signal modes, configured by DIP switch.
- Thermal management: a brushless fan is mounted to the top cover, and an onboard temperature sensor limits output in stages to protect the driver.
- Protection: overcurrent and thermal protection are included, with LED indicators for status.
- Battery monitoring: a low battery voltage warning feature is built in.
- Clean switching: high-current MOSFETs switch at 16kHz for quiet motor operation.
- Enclosed design: top and bottom covers protect the board and provide fan mounting.
Specifications Explained
60A continuous and 100A peak: the continuous figure is the current each channel can sustain, while the 100A peak is a short burst of about one second before the driver automatically limits output. Match your motors and wiring to these limits.
10V to 45V input: one power input feeds both the motors and the driver electronics. Confirm your battery pack stays inside this window across its full charge and discharge range.
Control modes: PWM input suits microcontrollers such as Arduino or PIC, UART allows serial commands, analog input works with a potentiometer, and RC servo signal supports radio-control receivers. DIP switches select the mode, and common configurations are printed on the bottom cover.
2x3 header: the RC-friendly header accepts two RC extension cables for quick receiver wiring.
Compatibility and Requirements
The driver accepts PWM from microcontrollers, UART serial commands, analog voltage from a potentiometer and RC servo signals. It is designed for two DC brushed motors and a single DC power source within the 10V to 45V range. Note that polarity protection is not provided, so correct wiring polarity before applying power. Use proper wire and cable gauges for battery and motor connections.
Typical Uses
- Combat and sumo robots needing high current per side
- Dual-motor mobile platforms and robotic vehicles
- RC-controlled robot builds using mix mode drive
- Microcontroller-driven projects requiring serial or PWM motor control
Condition Note
This is a refurbished item: packaging was opened for testing, and the unit has been fully tested and confirmed in proper working condition. Refer to the manufacturer user manual for detailed configuration.

Quick specs
- Model Series
- MDDS Series
- Voltage Rating (V)
- 10 to 45
- Current Rating (A)
- 60 to 100
- Operating Voltage (VDC)
- 10V to 45V
- Peak Current (A)
- 100
- Continuous Discharge Current (A)
- 60






















