Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

An Arduino-compatible shield that connects a wired or wireless PS2 controller to your board over UART. Jumper selectors let you set the baud rate and TX/RX pins, so reading joystick and button states stays simple.

Key Highlights

  • Works with wired or wireless PlayStation 2 controllers
  • Jumper selectors for 9600, 57600 or 115200 baud
  • Selectable digital pins for UART TX and RX
  • Stackable side headers allow more shields on top
  • Powered from the Arduino board at 4.5 to 5.5 V
  • Compact 68 x 53 mm board with status LED

Ideal For

  • Arduino makers adding game controller input to a project
  • Robotics students building remote-controlled mobile robots
  • Educators teaching UART communication with Arduino
  • Hobbyists converting a PS2 controller into a custom input device

Buying Tip

Confirm which digital pins your project leaves free, then set the TX and RX jumpers to match before powering up.

Elecvora expert review

Our verdict

The Cytron Arduino PS2 Shield removes most of the work from using a PlayStation 2 controller with an Arduino board. Its jumper-based configuration makes it adaptable, though it is a focused board rather than a general-purpose input solution.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Simple UART output for joystick and button states
  • Jumper selection of baud rate and UART pins
  • Stackable headers keep other shields usable
  • Powered directly from the Arduino board

Cons

  • PS2 controller not included
  • Requires the provided Arduino library to work
  • Reset control is tied to analog pin A1

Best for

Arduino robotics and learning projects that need game controller input

Not ideal for

Projects using controllers other than a PS2 type

Specifications

Item TypeShield
Voltage Rating (V)4.5 to 5.5
Current Rating (A)0.1 to 0.5
Length (mm)68
Width (mm)53
Shipping Weight0.05 kg
Shipping Dimensions8 × 6.5 × 3 cm

What's in the box

  • 1 x Cytron Arduino PS2 Shield

Frequently Asked Questions

Which Arduino boards does this shield work with?
It is designed for Arduino UNO, Duemilanove, Mega and Leonardo, and may work with other pin-compatible boards.
Do I need a separate power supply?
No. The shield is powered by the Arduino main board and is rated for 4.5 to 5.5 V.
Does the package include a PS2 controller?
No, only the shield is included. A wired or wireless PS2 controller must be purchased separately.
How do I change the communication speed?
Use the jumper selector to choose 9600, 57600 or 115200 baud.
Can I use hardware and software UART?
Yes, the shield supports either hardware or software UART on the Arduino main board.
How do I reset the shield?
The shield's reset is connected to Arduino analog pin A1, which you can pull down to reset it.

Overview

The Cytron Arduino PS2 Shield gives your Arduino project a straightforward way to accept input from a Sony PlayStation 2 controller. Instead of building a protocol layer yourself, you plug the controller into the shield's standard connector and read joystick and button states as UART data. Both wired and wireless PS2 controllers are supported, and the shield automatically places the controller in analog mode.

Key Features

  • Standard connector for wired or wireless PS2 controller plugs
  • Jumper selector for UART baud rate: 9600, 57600 or 115200
  • Jumper selectors to assign the digital pins used for UART TX and RX
  • Status LED for quick visual confirmation
  • Vibrator motor on the PS2 controller is controllable
  • Stackable side headers for adding further shields
  • Reset line tied to Arduino analog pin A1, which can be pulled down to reset the shield

Specifications Explained

The shield is rated for 4.5 to 5.5 V and is powered by the Arduino main board, so no separate supply is needed. Current draw is low, between 0.1 and 0.5 A, which keeps it friendly to small robotic builds. The board measures 68 mm by 53 mm, a compact footprint that still leaves room for the controller connector and jumper headers. Because the UART pins and baud rate are set with jumpers, you can move the shield between projects and adapt it to the pins your design has free.

Compatibility and Requirements

The shield is designed for Arduino UNO, Arduino Duemilanove, Arduino Mega and Arduino Leonardo, and it may work with other pin-compatible main boards. You will need a compatible PS2 controller and the Arduino library provided for the shield. Either hardware or software UART can be used for communication with the main board.

Typical Uses

Typical applications include remote-controlled mobile robots, classroom Arduino exercises, joystick-driven mechanisms and any project where a familiar game controller is a better input device than a keyboard or a set of buttons.

What's in the Box

The package includes one Cytron Arduino PS2 Shield. A PS2 controller is not included and must be supplied separately.

Quick specs

Item Type
Shield
Voltage Rating (V)
4.5 to 5.5
Current Rating (A)
0.1 to 0.5
Length (mm)
68
Width (mm)
53
Shipping Weight
0.05 kg
See all specifications