Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A single-channel brushed DC motor driver rated for 13A continuous and 30A peaks, operating from 5V to 30V. Its solid-state NMOS H-bridge supports both sign-magnitude and locked-antiphase PWM for smooth, reliable speed and direction control.

Key Highlights

  • Single-channel bidirectional control of one brushed DC motor
  • 5V to 30V motor supply with no separate logic supply required
  • 13A continuous and 30A peak current for up to 10 seconds
  • Supports locked-antiphase and sign-magnitude PWM operation
  • Solid-state NMOS H-bridge for fast response and no relay wear
  • Accepts 3.3V and 5V logic level PWM signals

Ideal For

  • Robotics builders driving a single high-current brushed motor
  • Students and makers learning PWM motor control
  • Automated cart and buggy projects
  • Hobbyists upgrading from a relay-based driver
  • Prototyping work with 3.3V or 5V microcontrollers

Buying Tip

Check your motor's stall current against the 30A peak limit and keep continuous draw near 13A, since the board has no polarity protection and no heat sink.

Elecvora expert review

Our verdict

The MD10C is a practical single-channel driver for brushed motors that pull more current than small hobby boards can handle. Its solid-state H-bridge and dual PWM mode support make it flexible for robotics and automation builds.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • 13A continuous and 30A peak headroom for demanding motors
  • Runs from a single 5V to 30V motor supply
  • Supports both sign-magnitude and locked-antiphase PWM
  • 3.3V and 5V logic inputs suit most microcontrollers
  • Test and manual buttons simplify first-time checks

Cons

  • No polarity protection, so wiring mistakes can damage the board
  • Single channel only, so two motors need two boards
  • No UART, analog or RC servo signal control

Best for

Robotics and automation projects driving one brushed DC motor up to 13A continuous

Not ideal for

Builds needing multi-channel control or RC servo signal input

Specifications

Item TypeMotor Driver
Model SeriesMD Series
Voltage Rating (V)5 to 30
Current Rating (A)13 to 30
Model No. / NameMD10C
Operating Voltage (VDC)5 to 30
Peak Current (A)30
Continuous Discharge Current (A)13
Operating ModePWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
Arduino Shield (Y/N)No, can be used with Wire connection
No. of Channels1
Battery Protect. Mode (Y/N)Yes
LED IndicatorYes
Cooling FanNo
Test/Manual Button (Y/N)Yes
Polarity Protection (Y/N)NO
Dimensions (L x W x H) mm75x43x13
Weight (g)22
Shipping Weight0.025 kg
Shipping Dimensions9 × 5.5 × 2.5 cm

What's in the box

  • 1 x Cytron Enhanced 13Amp DC Motor Driver 30A peak MD10C Rev 3.0
  • 1 x 2510 PCB Connector, 3 Ways, Female
  • 1 x 2510 Terminal Pin
  • 4 x Plastic spacer, approximately 7mm

Frequently Asked Questions

What motor voltage does the MD10C support?
It accepts a motor supply from 5V to 30V. The same supply powers the board, so no separate logic voltage is required.
How much current can it handle?
The board is rated at 13A continuous and 30A peak for up to 10 seconds. Keep sustained loads within the continuous rating.
Which PWM modes are supported?
It supports both locked-antiphase and sign-magnitude PWM, with a PWM frequency up to 20kHz. It does not support UART, analog or RC servo signal control.
Can I use it with a 3.3V microcontroller?
Yes. The logic inputs accept both 3.3V and 5V levels. The board is not an Arduino shield, so it connects by wire.
What comes in the package?
You receive the MD10C Rev 3.0 board, a 3-way 2510 PCB connector, a 2510 terminal pin set and four plastic spacers of about 7mm.
Does it protect against reversed power wiring?
No. The board has no polarity protection, so double-check the supply connections before switching on.

Overview

The Cytron MD10C is a single-channel motor driver for brushed DC motors that need serious current. It is a solid-state design that replaces relay-based switching with a fully NMOS H-bridge, giving faster response and no mechanical contacts to wear out. The board runs from a motor supply of 5V to 30V and is rated at 13A continuous with a 30A peak lasting up to 10 seconds.

This is the enhanced revision of the MD10C, supporting both locked-antiphase and sign-magnitude PWM. That flexibility lets you choose the control method that suits your controller and your motor.

Key Features

  • Bidirectional control of one brushed DC motor on a single channel
  • Motor voltage range of 5V to 30V
  • 13A continuous, 30A peak for up to 10 seconds
  • 3.3V and 5V logic level inputs
  • Locked-antiphase and sign-magnitude PWM support
  • PWM frequency up to 20kHz, with output matching input frequency
  • Powered from the motor supply only, no external logic voltage needed
  • Test and manual buttons with LED indicators
  • Compact board measuring 75 x 43 x 13mm and weighing 22g

Specifications Explained

Current rating: The 13A continuous figure is the load the driver can carry for sustained running. The 30A peak rating applies only to short bursts of up to 10 seconds, which covers motor startup and sudden load spikes.

Voltage range: Any motor supply between 5V and 30V works, and the same rail powers the driver's logic, so a single battery or power supply is enough.

PWM modes: Sign-magnitude and locked-antiphase are two ways of encoding speed and direction in a PWM signal. The MD10C accepts either, so it fits a wider range of controller code and wiring schemes.

Logic levels: Inputs accept both 3.3V and 5V signals, covering common microcontroller boards. The board is not an Arduino shield, so it connects by wire.

Compatibility and Requirements

The MD10C needs a brushed DC motor, a motor power supply within 5V to 30V, and a PWM signal from a microcontroller or similar source. It is not designed for UART, analog or RC servo signal control. Battery protection mode is included, but the board does not provide polarity protection, so check wiring before powering up.

Typical Uses

Robotics platforms, motorised carts and buggies, automated mechanisms, and any build where one brushed motor needs speed and direction control at higher current than a small driver allows.

What's in the Box

The package includes the MD10C Rev 3.0 board, a 3-way 2510 PCB connector, a 2510 terminal pin set and four plastic spacers of roughly 7mm for mounting.

MD10C R3

Quick specs

Item Type
Motor Driver
Model Series
MD Series
Voltage Rating (V)
5 to 30
Current Rating (A)
13 to 30
Model No. / Name
MD10C
Operating Voltage (VDC)
5 to 30
See all specifications