
1 / 4 · Click to enlarge
AI Summary
A thumb-sized PPG pulse sensor module for Arduino that detects heart rate through skin contact on a finger, wrist or earlobe. Its Gravity connector makes plug-and-play wiring simple, and it draws under 10mA.
Key Highlights
- PPG optical sensing detects blood volume changes in tissue
- Compact 28 x 24 mm board with two belt-mounting holes
- Low operating current under 10mA for battery-friendly builds
- Gravity interface for quick plug-and-play connection
- Works at 3.3V with Raspberry Pi, Intel Edison, Joule and Curie
- Suitable for finger, wrist, earlobe or other skin contact points
Ideal For
- Arduino users learning biosignal and pulse sensing
- Students building wearable health-monitoring prototypes
- Makers experimenting with fitness and heart-rate projects
- Developers using Raspberry Pi, Intel Edison, Joule or Curie at 3.3V
- Prototypers who need a compact sensor that straps to a belt
Buying Tip
Check that your board can supply the correct input voltage and plan how you will connect the Gravity cable, since the IO Sensor Shield is the recommended interface for Arduino.
Elecvora expert review
Our verdict
A tidy, low-current PPG module that makes pulse sensing approachable for Arduino users thanks to its Gravity connector and small board size. It is a sensible starting point for biosignal prototypes rather than a finished medical device.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Gravity interface simplifies wiring
- Very low current draw under 10mA
- Compact 28 x 24 mm board with mounting holes
- Works at 3.3V with several common development boards
Cons
- Requires a separate microcontroller board
- Readings depend on steady skin contact
- Not a calibrated medical-grade instrument
Best for
Arduino and microcontroller users prototyping pulse sensing
Not ideal for
Anyone needing certified clinical heart-rate measurement
Specifications
| Operating Current (mA) | <10mA |
|---|---|
| Dimensions (L x W x H) mm | 28 x 24(mm), 1.102″ x 0.945″(in) |
| Shipping Weight | 0.020 kg |
| Shipping Dimensions | 5 × 5 × 1 cm |
What's in the box
- 1 x DFRobot Gravity Heart Rate Monitor Sensor for Arduino
Frequently Asked Questions
What technique does this sensor use?
Where should I place the sensor?
Which boards can I use it with?
How much current does it draw?
What is included in the package?
How do I connect it to an Arduino?
Overview
The DFRobot Gravity Heart Rate Monitor is a small sensor module that brings pulse detection to Arduino and other microcontroller projects. It is based on photoplethysmography (PPG), a straightforward optical technique that looks at blood volume changes in the microvascular bed of tissue. From that signal you can detect the pulsatile component of the cardiac cycle, which is what makes a heartbeat reading possible.
At roughly 28 x 24 mm, the board is small enough to fit into wearable prototypes and handheld builds. Two holes on the board let you attach it to a belt, and the sensing surface can be wrapped against a finger, wrist, earlobe or another area with good skin contact.
Key Features
- PPG-based sensing: an optical approach to detecting blood volume changes in tissue.
- Compact footprint: 28 x 24 mm, easy to place in tight enclosures.
- Low current draw: under 10mA, helpful for portable and battery-powered projects.
- Gravity interface: plug-and-play wiring that lowers the barrier to getting started.
- 3.3V operation: usable with Raspberry Pi, Intel Edison, Joule and Curie boards.
- Mounting holes: two holes for attaching the sensor to a belt or strap.
Specifications Explained
The operating current is listed as under 10mA. In practice this means the module adds very little load to your supply, which matters when you are prototyping on a small battery or planning a wearable.
The board measures 28 x 24 mm. That size leaves room for the sensing area and the two mounting holes while still fitting into compact builds. Shipping weight is about 0.020 kg and the shipping dimensions are 5 x 5 x 1 cm, so the package is light and easy to post.
Compatibility and Requirements
The sensor is designed for Arduino microcontrollers and uses a Gravity interface for simple connection. The IO Sensor Shield is the recommended way to connect it to an Arduino or other microcontroller. With a 3.3V input voltage it can also work with Raspberry Pi, Intel Edison, Joule and Curie boards. You will need a suitable microcontroller board and a way to connect the Gravity cable to it.
Typical Uses
This module suits biosignal learning projects, pulse-monitoring prototypes, fitness and wearable experiments, and any build where you want to bring a heartbeat signal into a microcontroller. Because it can be strapped to a belt or wrapped against the skin, it works well in projects that need the sensor held in place during movement.
What's in the Box
Package contents: 1 x DFRobot Gravity Heart Rate Monitor Sensor for Arduino.

Quick specs
- Operating Current (mA)
- <10mA
- Dimensions (L x W x H) mm
- 28 x 24(mm), 1.102″ x 0.945″(in)
- Shipping Weight
- 0.020 kg
- Shipping Dimensions
- 5 × 5 × 1 cm


















