Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

The DFRobot micro:Driver is an expansion board that adds motor and servo control to micro:bit and UNIHIKER M10/K10 boards. It offers four DC motor ports or two stepper ports, eight servo interfaces, and nine Gravity GPIOs over I2C.

Key Highlights

  • Adds 4 DC motor ports or 2 stepper motor ports via HR8833 driver
  • 8 servo interfaces with direct Vin connection for high current
  • 9 extended GPIO pins with Gravity standard interface
  • Uses only 2 I2C pins, leaving other GPIOs free
  • Compact 63mm x 58mm board with DC jack and wiring terminal
  • Plug-and-play for micro:bit and UNIHIKER M10/K10

Ideal For

  • Makers building small robots with micro:bit or UNIHIKER
  • STEAM educators teaching motor and servo control
  • Students learning robotics and electronics
  • hobbyists needing extra GPIOs with Gravity interface
  • Prototypers creating compact motorized projects

Buying Tip

Check that your power supply stays within 3.5V–5.5V DC and that your motors do not exceed 1.5A continuous per channel.

Elecvora expert review

Our verdict

The DFRobot micro:Driver packs motor, servo, and GPIO expansion into a tidy board that is easy to integrate with micro:bit and UNIHIKER. It is a solid choice for compact robotics projects where pin count and space are limited.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Saves GPIO pins by using only two I2C lines
  • Supports both DC and stepper motors
  • Eight servo interfaces with direct Vin
  • Gravity connectors simplify wiring

Cons

  • Requires a separate power source within 3.5V–5.5V
  • Motor current limited to 1.5A continuous per channel

Best for

Small robots and STEAM projects with micro:bit or UNIHIKER

Not ideal for

Projects needing higher voltage or current than the board supports

Specifications

Model No. / NameDriver Expansion Board
Digital Output0/3.3
GPIO Pins9 (P0, P1, P2, P8, P12–P16)
CommunicationI2C
Motor driver chipHR8833
Max Current Continuous (A)1.5A
Power Input3.5V–5.5V DC
Length (mm)63
Width (mm)58
Shipping Weight0.07 kg
Shipping Dimensions10 × 9 × 3 cm

What's in the box

  • 1 x DFRobot micro:Driver Expansion Board
  • 1 x Connector Cable

Frequently Asked Questions

Which boards are compatible with the micro:Driver?
It is compatible with micro:bit, UNIHIKER M10, and UNIHIKER K10 boards.
How many motors can I connect?
You can connect up to four DC motors or two stepper motors, and up to eight servos.
What power supply does the board need?
It requires a DC input between 3.5V and 5.5V, connected via the DC jack or wiring terminal.
Does it use many GPIO pins?
No, it communicates over I2C and uses only two pins, leaving the other GPIOs free.
What is included in the package?
The package includes the micro:Driver expansion board and a connector cable.
What is the maximum continuous current per motor channel?
The HR8833 driver supports a maximum continuous current of 1.5A per channel.

Overview

The DFRobot micro:Driver is a driver expansion board designed to add motion control to micro:bit and UNIHIKER M10/K10 boards. It combines motor drivers, servo outputs, and extra GPIO pins on a single compact board, making it a practical choice for robotics and STEAM projects where space and pin count matter.

Key Features

  • Motor and servo control: Four DC motor ports or two stepper motor ports are driven by an HR8833 chip, and eight servo interfaces are available with direct Vin connection for high current.
  • Extended GPIOs: Nine GPIO pins (P0, P1, P2, P8, P12–P16) are broken out using the Gravity standard interface, so sensors and modules can be connected without soldering.
  • Efficient I2C communication: The board communicates over I2C and occupies only two pins, leaving the remaining GPIOs free for other tasks.
  • Flexible power input: Power can be supplied between 3.5V and 5.5V DC through the onboard DC jack or wiring terminal.
  • Compact footprint: Measuring 63mm by 58mm, the board fits neatly into small robot chassis and classroom builds.

Specifications Explained

The HR8833 motor driver chip supports a maximum continuous current of 1.5A per channel, which is suitable for small to medium DC motors and steppers. The 3.5V–5.5V DC input range covers common battery packs and USB power sources. Nine GPIO pins are exposed, and the Gravity interface means compatible cables can be used directly. The digital output is 0/3.3V, matching the logic level of the host boards.

Compatibility and Requirements

The micro:Driver is compatible with micro:bit, UNIHIKER M10, and UNIHIKER K10 boards. It requires a power source within the 3.5V–5.5V DC range, connected via the DC jack or wiring terminal. A connector cable is included for hookup.

Typical Uses

This board is well suited to small mobile robots, line followers, and servo-driven mechanisms. It is also useful in educational settings where students need to control motors and servos without complex wiring. The extended Gravity GPIOs allow additional sensors to be added as projects grow.

What's in the Box

  • 1 x DFRobot micro:Driver Expansion Board
  • 1 x Connector Cable

Quick specs

Model No. / Name
Driver Expansion Board
Digital Output
0/3.3
GPIO Pins
9 (P0, P1, P2, P8, P12–P16)
Communication
I2C
Motor driver chip
HR8833
Max Current Continuous (A)
1.5A
See all specifications