Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A pack of four EasyMech 6000ZZ shielded stainless steel ball bearings with a 10 mm bore, 26 mm outer diameter and 8 mm width. The deep-groove shielded design handles combined radial and axial loads in RC, robotics and linear motion assemblies.

Key Highlights

  • Pack of four 6000ZZ deep-groove shielded ball bearings
  • 10 mm inner diameter, 26 mm outer diameter, 8 mm thickness
  • Stainless steel construction with metal ZZ shields
  • Each bearing weighs approximately 20 g
  • Supports combined radial and axial loads at high rotational speeds
  • Standard 6000-series dimensions for broad fitment

Ideal For

  • RC car and truck builders replacing hub or drivetrain bearings
  • FPV and drone makers needing compact shielded bearings
  • Robotics hobbyists building joints and pivots
  • Makers maintaining gearboxes, pumps and small machinery
  • Workshops keeping a small stock of 10x26x8 mm spares

Buying Tip

Measure your shaft and housing bore before ordering: the bearing only fits a 10 mm shaft in a 26 mm seat with 8 mm of clearance.

Elecvora expert review

Our verdict

A sensible four-pack of standard-size shielded bearings for builders who need a reliable 10x26x8 mm fit. The stainless steel body and ZZ shields make them a practical choice for RC, robotics and light machinery work.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Standard 6000-series dimensions simplify replacement
  • Shielded both sides for debris protection
  • Stainless steel construction resists corrosion
  • Four-piece pack covers a full assembly or spares
  • Lightweight at about 20 g each

Cons

  • Shields are not a full seal, so avoid submersion
  • Load capacity depends on correct installation and alignment
  • No installation tools included in the pack

Best for

RC, robotics and light machinery builders needing a 10x26x8 mm shielded bearing

Not ideal for

Applications requiring a fully sealed bearing for wet or submerged use

Specifications

Model No. / Name6000ZZ
Inner Diameter (mm)10
Outer Diameter (mm)26
Thickness (mm)8
Weight (g)20 (each)
Width (mm)8
Shipping Weight0.04 kg
Shipping Dimensions8 × 8 × 3 cm

What's in the box

  • 4 x EasyMech 6000ZZ shielded miniature ball bearings, 10x26x8 mm

Frequently Asked Questions

What do the 10x26x8 mm dimensions mean?
The 10 mm figure is the inner bore that fits onto a shaft, 26 mm is the outer diameter that fits into a housing, and 8 mm is the bearing width.
Are these bearings sealed or shielded?
They are shielded with metal ZZ covers on both sides. The shields block debris but are not a full seal, so the bearings should not be submerged.
Can I use them in an RC car or drone build?
Yes, provided your hub, mount or housing uses a 10 mm shaft and a 26 mm bore with 8 mm of clearance.
How many bearings are included?
The pack contains four 6000ZZ bearings, each weighing approximately 20 g.
Do I need any special tools to fit them?
No special tools are supplied, but a bearing press or a suitable driver is recommended to seat them squarely without damaging the rings.
How should I care for these bearings?
Keep the shields clean, avoid immersion in water or solvents, and replace the bearing if it becomes noisy or develops noticeable play.

Overview

The EasyMech 6000ZZ is a miniature deep-groove ball bearing built around a 10 mm bore, a 26 mm outer diameter and an 8 mm width. It arrives as a pack of four, so you have a matched set for a single assembly or a few spares for routine maintenance. Each bearing weighs roughly 20 g.

The ZZ suffix refers to the metal shields fitted on both sides of the bearing. These shields sit close to the inner ring and help keep dust, grit and other debris away from the balls and raceways, which is useful in workshops, outdoor RC use and machinery that runs in less-than-clean conditions.

Key Features

  • Deep-groove geometry: the raceway design supports radial loads as well as axial loads in both directions, making one bearing suitable for combined loading.
  • Shielded on both sides: metal ZZ shields guard the rolling elements from environmental debris.
  • Stainless steel construction: helps the bearing resist corrosion compared with standard carbon steel in damp or humid settings.
  • High-speed capability: the deep-groove layout is intended for applications needing high running accuracy at high rotational speeds.
  • Compact and light: at 10x26x8 mm and about 20 g each, the bearing fits tight envelopes without adding meaningful mass.

Specifications Explained

10 mm bore: this is the shaft diameter the bearing slides onto. Check that your axle, spindle or motor shaft measures 10 mm before ordering.

26 mm outer diameter: this is the size of the housing or bore the bearing presses into. A 26 mm seat gives a secure fit.

8 mm width: the overall thickness of the bearing, which matters when space between a hub and a housing wall is limited.

ZZ shield: the metal shields are non-contact, so they protect the internals without adding significant drag. They are not a full seal, so the bearing is not intended for submersion.

Compatibility and Requirements

Fitment depends on matching the three key dimensions: a 10 mm shaft, a 26 mm housing bore and 8 mm of available width. The 6000ZZ follows standard 6000-series sizing, so it can replace an existing bearing with the same 10x26x8 mm dimensions. No additional hardware is required beyond the shaft and housing.

Typical Uses

These bearings suit RC car hubs and drivetrains, FPV motor mounts, robotics joints and pivots, gearboxes, clutches, drives, compressors, pumps, turbines, printing and textile machinery, and linear motion assemblies. They are also a practical choice for workshop repairs and DIY builds that need a small shielded bearing.

What's in the Box

  • 4 x EasyMech 6000ZZ shielded miniature ball bearings, 10x26x8 mm

Quick specs

Model No. / Name
6000ZZ
Inner Diameter (mm)
10
Outer Diameter (mm)
26
Thickness (mm)
8
Weight (g)
20 (each)
Width (mm)
8
See all specifications