
1 / 5 · Click to enlarge
AI Summary
An L293D dual H-bridge shield that plugs onto ESP8266 ESP12E Dev Kit and NodeMCU boards to drive two DC motors or one stepper. It handles 4.5-36V motor supplies at up to 1.2A while keeping control and motor power separated.
Key Highlights
- Dual high-power H-bridge L293DD driver in a compact shield format
- Drives two DC motors or one stepper motor from one board
- Motor supply range of 4.5V to 36V with up to 1.2A drive current
- Separate motor and control power rails with onboard power switch
- Passes through ESP12E pins including SPI, UART, GPIO, AI and 3.3V
- Four control ports D1-D4 for direction and PWM of motors A and B
Ideal For
- Makers building WiFi-controlled robot cars with ESP8266
- Students learning dual H-bridge motor control
- Hobbyists adding a stepper motor to a NodeMCU project
- Prototypers combining sensors and motion on one ESP12E board
- Small robotics projects needing a compact driver shield
Buying Tip
Confirm your motor's running and stall current stays under the 1.2A drive rating and that your planned motor voltage sits within 4.5V to 36V before ordering.
Elecvora expert review
Our verdict
A practical, low-cost way to add motor drive to an ESP8266 project without building an H-bridge from scratch. It is best treated as a light-duty driver, since the 1.2A and 4W ratings limit the motors it can safely handle.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Simple plug-on shield for ESP12E and NodeMCU boards
- Drives two DC motors or one stepper from a single board
- Wide 4.5V to 36V motor supply range
- Separate control and motor power with onboard switch
- Pass-through pins keep sensors and peripherals accessible
Cons
- 1.2A drive current and 4W maximum power limit motor choice
- No heatsinking or current limiting mentioned in the data
- Requires a separate control supply within 4.5V to 9V
Best for
Small WiFi-controlled robots and stepper prototypes on ESP8266
Not ideal for
High-current or high-power motor applications beyond the 1.2A and 4W ratings
Specifications
| Item Type | L293D Motor Driver |
|---|---|
| Current Rating (A) | 1.2 |
| Voltage Rating (V) | 4.5 to 36 |
| Motor power supply Range | 4.5V ~ 36V |
| Control Voltage Range | 4.5V ~ 9V (10VMAX) |
| Logic Current (mA) | ≤60mA |
| Drive Current (A) | ≤1.2A |
| Max. Power (W) | 4W |
| Drive Type | Dual high-power H-bridge driver |
| Operating Temperature (°C) | -25 ℃ ~ + 125 ℃ |
| Dimensions (L x W x H) mm | 60 x 45 x 13 |
| Weight (g) | 20 |
| Shipping Weight | 0.022 kg |
| Shipping Dimensions | 12 × 8 × 2 cm |
What's in the box
- 1 x L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
Frequently Asked Questions
Which development boards does this shield fit?
How many motors can it drive?
What supply voltages does it need?
What is the maximum current per motor?
Can I still connect sensors while using the shield?
What is included with the board?
Overview
The L293D Motor Driver Board is an expansion shield designed for the ESP8266 ESP12E Dev Kit and NodeMCU Lua boards. It carries the L293DD dual high-power H-bridge driver, which allows a single WiFi-capable development board to control two DC motors or one stepper motor. The shield uses the ESP-12E I/O pins as its control interface, so no separate driver board or complex wiring is needed to get motors moving.
Control logic and motor power are kept on separate rails, and an onboard power switch is provided. With dimensions of 60 x 45 x 13 mm and a weight of about 20 g, the board adds motor drive without making your build bulky.
Key Features
- L293DD dual H-bridge: drives two DC channels or one stepper motor.
- Wide motor supply: 4.5V to 36V for the motor rail.
- Control supply: 4.5V to 9V, 10V maximum.
- Current handling: up to 1.2A drive current per the rated specification.
- Four control ports: D1, D2, D3 and D4 used for PWMA, PWMB, DA and DB.
- Pin pass-through: VIN, 3.3V, DIO, AIO, SDIO, UART, SPI, RST and EN remain reachable for sensors and peripherals.
Specifications Explained
The 4.5V to 36V motor power range means the board can run small hobby motors as well as higher-voltage DC motors within that window. Keep in mind that the L293D driver stage itself is rated to a maximum power of 4W, so choose motors and supply voltages that keep the combined load within that figure.
The logic side accepts 4.5V to 9V, with 10V as the absolute maximum, and draws no more than 60mA. That makes it easy to power the control section from a separate, stable source while the motor rail handles the heavier load. The 1.2A drive current rating is a limit, not a target, so motors that stall at high current should be avoided or current-limited.
The four control pins map to PWM and direction for each motor channel: PWMA and DA for motor A, PWMB and DB for motor B. This arrangement lets your code set speed with PWM and direction with a simple logic level.
Compatibility and Requirements
The board is built for the ESP12E Dev Kit and NodeMCU Lua development boards. You will need a compatible ESP8266 board, a motor power supply within the 4.5V to 36V range, and a control supply within 4.5V to 9V. Motors, jumper wires and the development board itself are not included. The shield exposes the ESP12E pinout, so sensors such as temperature, humidity, light, buzzer or relay modules can be connected alongside the motor driver.
Typical Uses
Common applications include WiFi-controlled robot cars, small two-wheeled platforms, stepper-based mechanisms, and classroom or prototype projects that need remote motor control over a network. The exposed SPI, UART, GPIO and analog pins make it practical to combine motion with sensor feedback in a single build.
What's in the Box
- 1 x L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
Quick specs
- Item Type
- L293D Motor Driver
- Current Rating (A)
- 1.2
- Voltage Rating (V)
- 4.5 to 36
- Motor power supply Range
- 4.5V ~ 36V
- Control Voltage Range
- 4.5V ~ 9V (10VMAX)
- Logic Current (mA)
- ≤60mA













