
1 / 8 · Click to enlarge
At a glance
Made by MIKROE, this mikroe modules is a good fit for makers, students and electronics hobbyists. Main specs: operating voltage (vdc) 3.3 to 5; interface I2C; compatibility mikroBUS. Check that your power source supplies 3.3 to 5 before connecting it.
Key Highlights
- Operating Voltage (VDC): 3.3 to 5
- Interface: I2C
- Compatibility: mikroBUS
Ideal For
- Arduino, ESP32 and Raspberry Pi projects
- School and college lab work
- Prototypes and test rigs
Buying Tip
Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.
Specifications
| Operating Voltage (VDC) | 3.3 to 5 |
|---|---|
| Interface | I2C |
| Compatibility | mikroBUS |
| Board Size (mm) | 28.6 x 25.4 mm |
| Shipping Weight | 0.04 kg |
| Shipping Dimensions | 6 × 3 × 1 cm |
Overview
The MIKROE COMPASS 7 CLICK (MIKROE-5190) – MMC5633NJL 3-Axis Digital Compass / Magnetic Field Sensor, I²C, mikroBUS, made by MIKROE, is listed in our mikroe modules range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.
Specifications explained
- Operating Voltage (VDC): 3.3 to 5 (match this to your power supply; too high a voltage can damage the part)
- Interface: I2C (confirm your cable or board uses the same connector)
- Compatibility: mikroBUS
- Board Size (mm): 28.6 x 25.4 mm (measure your mounting space before ordering)
- Shipping Weight: 0.04 kg (important for drones, RC models and anything you carry)
- Shipping Dimensions: 6 × 3 × 1 cm (measure your mounting space before ordering)
Before you order
Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.
MIKROE COMPASS 7 CLICK (MIKROE-5190) as its foundation uses the MMC5633NJL, a monolithic high-performance 3-axis AMR magnetic sensor from MEMSIC. It comes with an integrated drive circuit, signal processing circuit, and serial interface block, allowing low noise and high resolution. It can measure magnetic fields within the full-scale range of ±30 Gauss (G) with up to 0.0625mG per LSB resolution at 20bits operation mode and 2mG total RMS noise level, enabling heading accuracy of ±1º in electronic compass applications.
An integrated SET/RESET function eliminates errors due to Null Field output change with temperature. In addition, it clears the sensors of any residual magnetic polarization resulting from exposure to strong external magnets. The SET/RESET function can be performed periodically for each measurement as the specific application requires.
Compass 7 Click communicates with MCU using the standard I2C 2-Wire interface with a maximum clock frequency of 400kHz, fully adjustable through software registers. The MMC5633NJL does not require a specific Power-Up sequence but requires a voltage of 1.8V for its interface and logic part to work correctly. Therefore, a small regulating LDO is used, the MAX8511, providing a 1.8V out of mikroBUS™ power rails. Since the sensor for operation requires a power supply of 1.8V, this Click board™ also features the PCA9306 voltage-level translator allowing the MMC5633NJL to work with 3.3V and 5V MCU properly.
This Click board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to use the communication lines properly. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.
Applications: Can be used as an electronic compass but also can be used in various position sensing applications
Features:
- Type Compass, Magnetic
- Interface: I2C
- On-board modules: MMC5633NJL - monolithic high-performance 3-axis AMR magnetic sensor from MEMSIC
- Low power consumption,
- Superior dynamic range and accuracy,
- On-chip automatic degaussing with built-in SET/RESET function,
- Sensitivity compensation and on-chip temperature sensor
Package Includes:
1 x MIKROE COMPASS 7 CLICK (MIKROE-5190) – MMC5633NJL 3-Axis Digital Compass / Magnetic Field Sensor, I²C, mikroBUSQuick specs
- Operating Voltage (VDC)
- 3.3 to 5
- Interface
- I2C
- Compatibility
- mikroBUS
- Board Size (mm)
- 28.6 x 25.4 mm
- Shipping Weight
- 0.04 kg
- Shipping Dimensions
- 6 × 3 × 1 cm


















