
1 / 3 · Click to enlarge
AI Summary
A 3S1P lithium-ion pack using matched INR P42A cells, delivering 11.1V nominal and 4200mAh for 4-inch FPV drones. Its triangle shape, XT30 discharge port and roughly 240 g weight make it a compact option for builds that need more capacity per gram.
Key Highlights
- 3S1P lithium-ion pack with 11.1V nominal and 4200mAh capacity
- 11C continuous discharge rating for moderate-current FPV setups
- Triangle cell layout sized for 4-inch FPV drone frames
- XT30 discharge port plus JST-XH and JST-RCY BEC charge leads
- Impedance-matched INR P42A cells for consistent pack performance
- Compact footprint of 70 x 45 mm at roughly 240 g
Ideal For
- FPV pilots building or flying 4-inch drone frames
- Cruisers and cinematic flyers wanting longer flight time
- Builders who prefer lithium-ion packs over lithium-polymer
- Pilots already using XT30 power connections
- Makers needing a compact 3S pack with balance leads
Buying Tip
Check your build's maximum current draw against the 11C continuous rating and confirm your frame fits a 70 x 45 mm triangle pack before ordering.
Elecvora expert review
Our verdict
A sensible 3S lithium-ion option for 4-inch FPV builds that value capacity per gram and a compact triangle footprint. It is not a high-current pack, so match it to a moderate-draw setup.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- 4200mAh capacity in a pack of roughly 240 g
- Impedance-matched INR P42A cells
- Triangle layout fits 4-inch frames neatly
- XT30 discharge plus JST-XH and JST-RCY BEC leads
Cons
- No onboard BMS, so protection relies on your electronics
- 11C continuous rating limits high-current builds
- Requires a charger that supports 3S lithium-ion packs
Best for
4-inch FPV cruisers and cinematic builds with moderate current draw
Not ideal for
High-current racing quads or setups needing an integrated BMS
Specifications
| Nominal Voltage (V) | 11.1 |
|---|---|
| Nominal Capacity (mAh) | 4200 mAh |
| Continuous Discharge Current (A) | 11C |
| BMS (Y/N) | N |
| Charge Connector | 4 Pin JST XH/2 Pin JST RCY BEC Female |
| Discharge Port | Amass XT30 |
| Max. Charging Voltage (V) | 12.6 |
| Max. Discharging Voltage (V) | 8.7 |
| Charging Current | 5C |
| Length (mm) | 70 |
| Width (mm) | 45 |
| Weight (g) | ~240 |
| Model Series | 3 |
| Shipping Weight | 0.295 kg |
| Shipping Dimensions | 13 × 11 × 6 cm |
What's in the box
- 1 x Pro-Range INR P42A 11.1V 4200mAh 11C 3S1P 4" FPV Drone Triangle Li-ion Battery Pack with XT-30 & JST-RCY-BEC
Frequently Asked Questions
What voltage should I set my failsafe to?
Can I charge this pack with a standard lithium-polymer charger?
Does this battery have built-in protection?
What connectors does it use?
What is included in the box?
How should I store the pack?
Overview
The Pro-Range INR P42A 11.1V 4200mAh pack is a 3S1P lithium-ion battery assembled for 4-inch FPV drones. Its three cells sit in a triangle arrangement that measures 70 mm long and 45 mm wide, and the complete pack weighs about 240 g. Nominal voltage is 11.1V, rising to 12.6V when fully charged and dropping to a recommended 8.7V minimum under load.
Each pack is built from INR P42A cells that are impedance matched, so the cells work together rather than one carrying more load than the others. The pack has no internal BMS, which means protection and voltage monitoring are handled by your drone's electronics and your charger.
Key Features
- 3S1P configuration: 11.1V nominal from three cells in series.
- 4200mAh capacity: useful flight time for 4-inch FPV builds.
- 11C continuous discharge: suited to moderate current draw.
- XT30 discharge port: a compact connector common on small FPV power leads.
- Dual charge leads: 4-pin JST-XH and 2-pin JST-RCY BEC female connectors.
- Triangle form factor: shaped to sit neatly on 4-inch frames.
Specifications Explained
Voltage window
Treat 12.6V as the full-charge ceiling and 8.7V as the lowest voltage you should fly down to. Many pilots set a battery failsafe around 9.6V to keep a reserve before landing.
Capacity and discharge
At 4200mAh, the pack stores more energy than a typical small 3S lithium-polymer brick of similar weight. The 11C continuous rating describes how much current the pack is built to deliver steadily; check your build's current draw against that figure rather than assuming unlimited power.
Charging
The pack is rated for 5C charging, but the charge current you actually use should match your charger's balance lead capability and your own risk tolerance. The 4-pin JST-XH lead provides per-cell balance access, while the JST-RCY BEC lead is a separate 2-pin connection.
No BMS
Because there is no onboard battery management system, low-voltage cutoff, over-current protection and balancing all depend on your drone and charger setup.
Compatibility and Requirements
Use a charger that supports 3S lithium-ion packs and can connect to the 4-pin JST-XH balance lead. Your drone's power lead must terminate in an XT30 plug to match the discharge port. Confirm that your frame accepts a triangle pack of about 70 x 45 mm and that your current draw stays within the 11C continuous rating.
Typical Uses
This pack suits 4-inch FPV drones flown for cruising, cinematic lines and general freestyle where a lighter lithium-ion pack is preferred over a heavier lithium-polymer alternative. It is also a reasonable choice for builds that benefit from the triangle layout and the extra capacity per gram.
What's in the Box
- 1 x Pro-Range INR P42A 11.1V 4200mAh 11C 3S1P 4" FPV Drone Triangle Li-ion Battery Pack with XT-30 & JST-RCY-BEC

Quick specs
- Nominal Voltage (V)
- 11.1
- Nominal Capacity (mAh)
- 4200 mAh
- Continuous Discharge Current (A)
- 11C
- BMS (Y/N)
- N
- Charge Connector
- 4 Pin JST XH/2 Pin JST RCY BEC Female
- Discharge Port
- Amass XT30


















