
1 / 5 · Click to enlarge
AI Summary
A compact XT60 inline power module that feeds ArduPilot and PX4 flight controllers 5.3V from 2S–14S packs while sensing voltage up to 60V and current up to 120A. It combines a regulated BEC, precision shunt sensing and TVS protection on a 29g board.
Key Highlights
- Handles 2S–14S LiPo input from 9V to 60V DC
- Regulated 5.3V BEC with 3A continuous and 5A peak output
- Precision shunt current sensing up to 120A burst
- Voltage sensing to 60V with a 20.66 divider ratio
- Rubycon 330µF low-ESR capacitor and TVS spike protection
- Compact 30 × 22 mm XT60 inline board weighing 29g
Ideal For
- ArduPilot multirotor builders using 6S to 14S packs
- PX4 fixed-wing and VTOL developers needing power telemetry
- FPV long-range pilots running high-voltage LiPo setups
- Robotics teams integrating a regulated 5.3V rail
- UAV technicians servicing analog power modules
Buying Tip
Check that your autopilot's power port matches the JST-GH 6-pin interface and set the 20.66 divider ratio and 40 A/V scaling in your firmware before the first flight.
Elecvora expert review
Our verdict
The HVPM-01A packs a wide 2S–14S input range, a 3A BEC and 120A-capable sensing into a 29g inline board, which is a sensible combination for high-voltage ArduPilot and PX4 builds. It is an analog module, so expect to spend time on firmware calibration to get the best accuracy.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Wide 9V–60V input covers 2S to 14S packs
- Regulated 5.3V output with 3A continuous and 5A peak
- Precision shunt sensing with TVS and low-ESR capacitor protection
- Compact 30 × 22 mm XT60 inline format at 29g
Cons
- Requires firmware calibration to reach the stated ±2% accuracy
- Analog sensing rather than digital telemetry
- Recommended continuous current is 60A, so very high-draw builds need care
Best for
ArduPilot and PX4 UAVs running 2S–14S LiPo packs that need a regulated supply and power telemetry
Not ideal for
Pilots wanting plug-and-play digital power data without firmware setup
Specifications
| Shipping Weight | 0.038 kg |
|---|---|
| Shipping Dimensions | 12 × 9 × 2 cm |
What's in the box
- 1 x SwiftWing HVPM-01A High Voltage Analog Power Module (2S–14S, 60V) for ArduPilot & PX4
- 2 x JST power cable
Frequently Asked Questions
Which flight controllers does the HVPM-01A work with?
What battery range does it support?
How much current can it supply to the flight controller?
How accurate are the voltage and current readings?
What is included with the module?
What are the operating and storage temperatures?
Overview
The SwiftWing HVPM-01A is an analog power module for UAV platforms that use ArduPilot or PX4 flight controllers. It sits inline on the main battery lead through an XT60 connection, drawing from a 2S–14S LiPo pack and delivering a regulated 5.3V supply to the autopilot. At the same time it measures pack voltage and current draw, giving the flight controller the data it needs to monitor power consumption and battery health.
The board is deliberately compact: 30 × 22 mm, 1.6 mm thick and 29g, built on a 4-layer PCB with 2 oz copper. That makes it a practical fit for multirotor, VTOL and fixed-wing airframes where weight and space matter.
Key Features
- Wide input range: 9V to 60V DC, covering 2S through 14S LiPo packs.
- Regulated BEC: 5.3V ±3% output at 3A continuous and 5A peak for under 3 seconds, with efficiency up to 90%.
- Dual sensing: voltage measurement from 0 to 60V and current measurement from 0 to 120A using a precision shunt.
- Stability and protection: a 330µF 63V Rubycon low-ESR input capacitor plus TVS transient voltage suppression.
- Simple interface: JST-GH 6-pin connector to the flight controller and an XT60 inline layout.
Specifications Explained
The input range is the headline figure. Because the module accepts 9V to 60V, it works across small 2S builds and large 14S platforms without a separate regulator. The 5.3V BEC output keeps the flight controller fed at 3A continuous, with 5A peaks for short demand spikes such as servo activity or startup.
Sensing accuracy depends on calibration, and the module is rated at ±2% after calibration. The voltage divider ratio of 20.66 and the 40 A/V current scaling are the values you enter into the autopilot's power configuration so it can convert raw analog readings into usable voltage and current figures. Recommended continuous current is 60A, with a 120A maximum burst.
Compatibility and Requirements
The HVPM-01A is intended for ArduPilot and PX4 systems and connects through a JST-GH 6-pin interface. It is compatible with 2S–14S LiPo batteries and uses XT60 connectors inline on the battery lead. Two JST power cables are supplied. Operating temperature is -10°C to +60°C, with storage from -20°C to +85°C.
Typical Uses
Multirotor, VTOL and fixed-wing UAVs that need a regulated supply and reliable power telemetry from a single module. It also suits robotics platforms built around ArduPilot or PX4 that run on LiPo packs within the stated range.
What's in the Box
- 1 x SwiftWing HVPM-01A High Voltage Analog Power Module
- 2 x JST power cable



















