Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A 300 mm DroneCAN/UAVCAN cable with JST-GH 4-pin connectors on both ends and a twisted CAN_H/CAN_L pair. It gives flight controllers and CAN modules a short, noise-resistant link with straight pin-to-pin wiring.

Key Highlights

  • JST-GH 4-pin connectors on both ends
  • 300 mm length for tidy, short cable runs
  • Twisted CAN_H and CAN_L pair for noise immunity
  • 28 AWG tinned copper conductors
  • Straight pin-to-pin wiring, no crossover
  • Crimp terminals pull-test verified

Ideal For

  • Drone builders wiring DroneCAN or UAVCAN nodes
  • Industrial UAV technicians maintaining CAN networks
  • FPV pilots adding CAN peripherals to a flight controller
  • Bench testers checking CAN modules before installation
  • Makers replacing a damaged 4-pin CAN lead

Buying Tip

Check your device's 4-pin header is JST-GH and confirm the pin order matches straight-through wiring before connecting power.

Elecvora expert review

Our verdict

A well-considered short CAN lead: the twisted pair and verified crimps address the two most common failure points in DroneCAN wiring. It is a sensible spare to keep in a build kit rather than a specialist component.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Twisted CAN_H/CAN_L pair supports noise rejection
  • Pull-test verified crimp terminals
  • Straight pin-to-pin wiring avoids signal mix-ups
  • Compact 300 mm length suits small airframes

Cons

  • Only 300 mm, so not suited to long runs
  • Requires matching JST-GH 4-pin sockets on both devices
  • Pin order must be checked before powering up

Best for

Short DroneCAN or UAVCAN links inside compact UAV builds

Not ideal for

Long cable runs or hardware with non-JST-GH connectors

Specifications

Shipping Weight0.005 kg
Shipping Dimensions9 × 6 × 2 cm

What's in the box

  • 1 x DroneCAN Cable (JST-GH 4-Pin to JST-GH 4-Pin, 300 mm)

Frequently Asked Questions

What is this cable used for?
It carries DroneCAN or UAVCAN data between compatible devices, such as a flight controller and a CAN-enabled module. Both ends are JST-GH 4-pin connectors.
How long is the cable?
The cable is 300 mm long, which suits short internal runs in compact airframes.
Does it work with any 4-pin connector?
No. It is built for JST-GH 4-pin sockets, so check your hardware uses that connector type before ordering.
Is the wiring crossed or straight?
The wiring is straight pin to pin, so signal positions are the same at both ends.
What is included in the package?
One DroneCAN Cable with JST-GH 4-pin connectors on both ends, 300 mm long.
How should I care for the cable?
Avoid sharp bends and pulling on the wires when unplugging; grip the connector body instead. Check the crimps periodically if the cable is handled often.

Overview

The SwiftWing DroneCAN Cable connects DroneCAN and UAVCAN devices to a flight controller or to each other. It measures 300 mm and terminates in JST-GH 4-pin connectors at both ends, so it fits the small 4-pin headers commonly used on CAN-enabled drone electronics. The cable is intended for builders who want a clean, correctly wired link rather than adapting a generic lead.

Key Features

  • JST-GH 4-pin connectors at both ends for direct plug-in to matching headers.
  • Twisted CAN_H and CAN_L pair to help limit interference from nearby power and motor wiring.
  • 28 AWG tinned copper conductors for flexible, corrosion-resistant signal wiring.
  • Straight pin-to-pin wiring so signal order stays consistent end to end.
  • Pull-test verified crimps for connectors that resist loosening with handling.
  • 300 mm length that keeps wiring short and organised in compact frames.

Specifications Explained

The 4-pin JST-GH format is the connector standard this cable is built around; check that your device uses a matching 4-pin JST-GH socket before ordering. The 300 mm length is best suited to short runs inside a single airframe, where a longer lead would need coiling or tying back.

Wire gauge matters for signal integrity: 28 AWG tinned copper is light and flexible, and the tinning helps protect the strands. The twisted CAN_H and CAN_L pair is the detail that supports reliable data in electrically noisy UAV environments, since twisting helps cancel induced noise on the differential pair. Straight-through pin-to-pin wiring means the cable does not swap signal positions, and the verified crimp terminals reduce the chance of an intermittent connection.

Compatibility and Requirements

This cable is designed for DroneCAN and UAVCAN-enabled devices and flight controllers that accept JST-GH 4-pin connections. Both ends are the same connector type, so it links two compatible 4-pin ports. Confirm the pin arrangement of your hardware matches the straight-through layout before powering up.

Typical Uses

  • Linking a DroneCAN or UAVCAN peripheral to a flight controller
  • Wiring CAN nodes inside industrial UAV assemblies
  • Bench testing CAN modules before installation
  • Replacing a damaged or poorly crimped CAN lead
  • Keeping short, tidy runs in compact airframes

What's in the Box

1 x DroneCAN Cable (JST-GH 4-Pin to JST-GH 4-Pin, 300 mm).

Quick specs

Shipping Weight
0.005 kg
Shipping Dimensions
9 × 6 × 2 cm
See all specifications