Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

This compact module uses an ACS712 Hall effect sensor to measure AC or DC current up to 30A and outputs a proportional analog voltage. Its 100 mV/A sensitivity and 5V operation make it easy to connect to Arduino and other microcontrollers.

Key Highlights

  • Measures AC or DC current up to 30A
  • 100 mV/A output sensitivity for clear readings
  • Operates from a 4.5–5.5V single supply
  • Analog output connects directly to microcontroller ADCs
  • Compact 27 x 12 mm board weighs only 5 g
  • Hall effect sensing provides electrical isolation

Ideal For

  • Arduino and microcontroller hobbyists building current monitoring projects
  • Electronics students learning about Hall effect sensors
  • Makers designing over-current protection circuits
  • Engineers prototyping battery chargers or power supplies
  • Robotics enthusiasts adding current feedback to motor drivers

Buying Tip

Check that your project's current stays within the 30A range and that you have a 5V supply and an analog input available on your microcontroller.

Elecvora expert review

Our verdict

A practical, low-cost current sensing solution for hobbyists and prototypers who need to measure up to 30A with minimal setup. The analog output and 5V operation make it easy to integrate with common microcontroller boards.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Measures both AC and DC current
  • Simple analog interface works with most microcontrollers
  • Compact and lightweight board
  • Inherent isolation from the measured circuit
  • Linear output simplifies calibration

Cons

  • Requires an external 5V supply
  • No onboard amplification or filtering
  • Limited to 30A maximum current

Best for

Arduino-based current monitoring and protection projects

Not ideal for

High-precision laboratory measurements or currents above 30A

Specifications

Sensitivity (mV/A)100
Length (mm)27
Width (mm)12
Weight (g)5
Supply Voltage4.5 ~ 5.5

What's in the box

  • 1 x 30A Range Current Sensor Module ACS712

Frequently Asked Questions

Can this module measure both AC and DC current?
Yes, the ACS712 sensor is designed to measure AC or DC current up to 30A. The output voltage will be proportional to the instantaneous current.
What is the output voltage range?
The output is ratiometric to the supply voltage and centered at half the supply voltage when no current flows. With a 5V supply, the output swings approximately 0 to 5V over the current range.
Do I need a separate power supply for the module?
Yes, the module requires a regulated 4.5–5.5V supply. It can often be powered from the same 5V source that powers your microcontroller, provided it can supply enough current.
Is the module compatible with 3.3V microcontrollers?
The module is specified for 4.5–5.5V operation, so it is best used with 5V systems. If using a 3.3V microcontroller, you may need level shifting or a voltage divider on the output.
What is included in the package?
The package includes one 30A Range Current Sensor Module ACS712. No cables or connectors are included unless stated otherwise.
How do I connect a load to the module?
The current-carrying conductor is connected through the module's terminal block. Ensure the current does not exceed 30A and observe proper polarity for accurate readings.

Overview

The ACS712 30A Current Sensor Module is a compact breakout board built around a Hall effect current sensor IC. It lets you measure AC or DC current up to 30A and outputs an analog voltage that is proportional to the current flowing through the board's copper conduction path. Because the sensing element is magnetic rather than resistive, the module provides inherent isolation between the current-carrying circuit and the low-voltage output, which is useful when working with mains-powered equipment or high-current loads.

Key Features

  • Wide current range: Detects AC or DC current up to 30A, covering many hobby and light industrial applications.
  • High sensitivity: 100 mV/A output makes small current changes easier to resolve with a standard ADC.
  • Single-supply operation: Runs from 4.5V to 5.5V, matching common 5V microcontroller boards.
  • Compact footprint: The 27 x 12 mm board and 5 g weight allow easy integration into tight enclosures.
  • Analog interface: The output voltage can be read directly by an Arduino or any microcontroller with an analog input.

Specifications Explained

Sensitivity (100 mV/A): For every ampere of current flowing through the sensor, the output voltage changes by about 100 millivolts. This gives a predictable linear relationship that you can calibrate in software.

Supply Voltage (4.5–5.5V): The module is designed for 5V systems. It will work with a regulated 5V supply and is compatible with 5V logic microcontrollers. Avoid applying voltages outside this range.

Dimensions (27 x 12 mm) and Weight (5 g): The small board size and light weight make it suitable for embedded installations where space and payload matter.

Compatibility and Requirements

The module outputs an analog voltage, so it requires a microcontroller or ADC with an analog input capable of reading 0–5V. It is commonly used with Arduino boards and similar 5V development platforms. A stable 5V supply is recommended for accurate readings. No additional components are required for basic operation, though you will need to provide wiring and a way to connect the current-carrying conductor to the module's terminals.

Typical Uses

  • Over-current protection circuits
  • Battery chargers and power supplies
  • Digital watt meters and energy monitors
  • Programmable current sources
  • General current sensing in robotics and automation projects

What's in the Box

1 x 30A Range Current Sensor Module ACS712.

arduino_ACS712arduino_ACS712

Quick specs

Sensitivity (mV/A)
100
Length (mm)
27
Width (mm)
12
Weight (g)
5
Supply Voltage
4.5 ~ 5.5
See all specifications