
1 / 3 · Click to enlarge
AI Summary
A compact ACS712ELC-5A breakout that measures -5A to +5A AC or DC current and outputs an analog voltage at 100mV/A. Its single 5V supply and small 32 x 13mm footprint make it easy to add current sensing to microcontroller projects.
Key Highlights
- ACS712ELC-5A Hall-effect sensor for AC and DC current
- Bidirectional measuring range of -5A to +5A
- Linear analog output at 100mV per amp
- Single 4.5V to 5.5V supply operation
- Compact 32mm x 13mm board weighing 5g
- Analog output reads directly on a microcontroller ADC pin
Ideal For
- Arduino and microcontroller hobbyists adding current sensing
- Makers building digital watt meters or power monitors
- Students learning Hall-effect current measurement
- Engineers prototyping over-current protection circuits
- DIY battery charger and power supply builders
Buying Tip
Check that your load stays within the -5A to +5A range; for higher currents, choose a 20A or 30A ACS712 variant instead.
Elecvora expert review
Our verdict
A practical, low-cost current sensing board that is easy to integrate thanks to its analog output and single 5V supply. It suits small-load projects well, but the 5A ceiling and need for calibration limit it to modest applications.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Simple analog interface works with most microcontroller ADCs
- Handles both AC and DC current in two directions
- Compact 32mm x 13mm board with low 5g weight
- Single 4.5V to 5.5V supply simplifies wiring
Cons
- Limited to a -5A to +5A range
- Requires calibration against a known reference
- Board colour may vary from the product images
Best for
Small-load current monitoring in microcontroller and Arduino projects
Not ideal for
High-current loads above 5A or precise metering without calibration
Specifications
| Operating Voltage (V) | 4.5 to 5.5 |
|---|---|
| Chip | ACS712ELC-5A |
| Measuring Current Range | -5 ~ +5A |
| Sensitivity (mV/A) | 100mV/A |
| Length (mm) | 32 |
| Width (mm) | 13 |
| Weight (g) | 5 |
| Supply Voltage | 4.5 ~ 5.5 |
What's in the box
- 1 x 5A Range Current Sensor Module ACS712
Frequently Asked Questions
Can this module measure both AC and DC current?
What supply voltage does it need?
How do I read the current value?
What is included with the module?
Does it come with cables or a microcontroller?
How should I handle the module?
Overview
The ACS712 5A Current Sensor Module gives your project a straightforward way to measure current. At its heart is the ACS712ELC-5A, a linear Hall-effect sensor that converts the magnetic field around an internal copper conduction path into a proportional output voltage. The board accepts a single supply between 4.5V and 5.5V and delivers an analog signal at 100mV/A, so a microcontroller with an analog-to-digital converter can read the current flow.
Because the sensor works on the Hall principle, it handles both AC and DC current and measures in both directions, from -5A to +5A. The module is small at 32mm by 13mm and weighs about 5g, making it simple to mount inside compact builds.
Key Features
- ACS712ELC-5A sensor: factory-trimmed Hall-effect IC with a low-noise analog signal path
- Wide measuring range: -5A to +5A bidirectional current sensing
- Predictable scaling: 100mV/A output sensitivity simplifies conversion in firmware
- Flexible supply: operates from 4.5V to 5.5V on a single rail
- Compact size: 32mm x 13mm board, 5g weight
- Analog output: connects to a standard ADC input on common development boards
Specifications Explained
Measuring range and sensitivity
The -5A to +5A range covers small loads such as individual motor channels, LED strings or low-power chargers. With 100mV/A sensitivity, each amp of current changes the output by about 0.1V, and the direction of current is reflected by whether the output sits above or below its zero-current level.
Supply voltage
A 4.5V to 5.5V supply matches typical 5V microcontroller boards. Keep the supply within this window for the output to scale as expected.
Size and weight
At 32mm long, 13mm wide and roughly 5g, the module adds very little bulk to a build and can sit close to the load being measured.
Compatibility and Requirements
The module outputs an analog voltage, so it needs a host device with an analog input, such as an Arduino-style board. It requires a 4.5V to 5.5V supply and wiring for the current path through the module terminals plus connections for supply, ground and signal. No other components are included, and the product colour may vary between shipments.
Typical Uses
- Over-current protection circuits
- Battery chargers
- Switching mode power supplies
- Digital watt meters
- Programmable current sources
- General AC or DC current monitoring in microcontroller projects
What's in the Box
One 5A Range Current Sensor Module ACS712. Note that the board colour may vary, and you may receive any available variant.


Quick specs
- Operating Voltage (V)
- 4.5 to 5.5
- Chip
- ACS712ELC-5A
- Measuring Current Range
- -5 ~ +5A
- Sensitivity (mV/A)
- 100mV/A
- Length (mm)
- 32
- Width (mm)
- 13

















