Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A five-pack of 9 x 9 mm aluminum heatsinks with pre-applied thermal tape, made for A4988 and DRV8825 stepper motor driver boards. Each sink presses on in seconds to help spread heat away from the driver chip.

Key Highlights

  • Five 9 x 9 mm aluminum heatsinks in one set
  • Pre-applied thermally conductive adhesive tape for tool-free mounting
  • Aluminum body for efficient heat spreading
  • Only about 4 g total weight for all five pieces
  • Fits A4988 and DRV8825 stepper motor driver boards
  • Compact 4 x 3 x 3 cm shipping size, easy to store

Ideal For

  • 3D printer owners running A4988 or DRV8825 driver boards
  • CNC and engraving builders using small stepper driver modules
  • Robotics hobbyists assembling multi-axis motion setups
  • Makers maintaining several driver boards at once
  • Anyone replacing worn or loose heatsink tape on a driver chip

Buying Tip

Clean the driver chip with isopropyl alcohol and let it dry fully before pressing a heatsink on, so the pre-applied tape makes proper contact.

Elecvora expert review

Our verdict

A simple, low-cost five-pack that makes it easy to add a bit of heat spreading to A4988 and DRV8825 driver chips. The pre-applied tape keeps installation quick, though the small 9 x 9 mm size means it covers the chip rather than the whole board.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Five sinks in one pack for multiple boards
  • Pre-applied thermal tape needs no extra paste or clips
  • Lightweight aluminum construction
  • Compact size suits small driver chips

Cons

  • Adhesive tape is not reusable once removed
  • Small footprint covers only the chip area
  • No datasheet or thermal rating supplied

Best for

Makers adding basic heat spreading to A4988 or DRV8825 driver boards

Not ideal for

High-power driver setups that need a larger, mechanically fixed cooler

Specifications

Model SeriesDRV Series, Heat Sink
Length (mm)9
Width (mm)9
Weight (g)4 (Weight of 5Pcs)
Shipping Weight0.02 kg
Shipping Dimensions4 × 3 × 3 cm

What's in the box

  • 5 x Aluminum heatsinks for A4988 and DRV8825 stepper motor drivers

Frequently Asked Questions

How do I attach these heatsinks?
Peel the protective film from the adhesive side and press the sink gently onto the driver chip. No screws or thermal paste are needed.
Which driver boards are these made for?
They are listed for A4988 and DRV8825 stepper motor driver boards.
How many heatsinks are included?
The pack contains five aluminum heatsinks, each 9 x 9 mm.
Do the heatsinks need a power supply?
No. They are passive aluminum parts and require no power or wiring.
Can I remove and reattach a heatsink?
The adhesive tape is intended for one fitting. Once removed, it may not hold securely again without fresh tape.
How should I store spare heatsinks?
Keep them in a dry place and leave the protective film on until you are ready to fit them.

Overview

Stepper motor driver boards such as the A4988 and DRV8825 run small surface-mount chips that can warm up during sustained motion-control work. This set gives you five compact aluminum heatsinks designed to sit directly on those boards and help spread heat away from the driver chip. Each sink is 9 x 9 mm and carries thermally conductive adhesive tape on the mounting side, so installation needs no clips, screws or drilling.

The five-piece pack weighs only about 4 g in total, which means the sinks add almost nothing to the weight of a printed part, robot chassis or control enclosure. They ship in a small 4 x 3 x 3 cm package, so spares are easy to keep on hand.

Key Features

  • Five matching sinks: enough pieces for several driver boards or for keeping replacements ready.
  • Adhesive thermal tape: the mounting face is pre-covered, so you simply peel and press.
  • Aluminum construction: a material chosen for its heat-spreading behaviour.
  • Compact footprint: the 9 x 9 mm size suits small driver chips and tight board layouts.
  • Low weight: about 4 g for the full set of five.

Specifications Explained

9 x 9 mm length and width: this is a small sink intended to cover the driver chip area rather than the whole board. Check the space around the chip before fitting, especially if the board sits close to a case wall or another component.

About 4 g for five pieces: each sink is very light, so it will not stress the board or change the balance of a small assembly. The figure covers the full set, not a single piece.

Adhesive tape on the attaching side: the tape removes the need for thermal paste or mechanical fasteners. Press the sink gently onto a clean chip surface and let the adhesive do the holding.

Compatibility and Requirements

The heatsinks are listed for A4988 and DRV8825 stepper motor driver boards. No other tools, power source or controller is required to fit them. Because the sinks rely on adhesive tape, the mounting surface should be clean and free of dust or oil before you press them into place.

Typical Uses

These sinks are a practical addition to 3D printer control boards, CNC driver stacks, small robotics builds and other projects that use A4988 or DRV8825 driver modules. They are also useful as spares when you are assembling several boards at once or replacing an old sink whose tape has lost grip.

What's in the Box

  • 5 x Aluminum heatsinks for A4988 and DRV8825 stepper motor drivers

Quick specs

Model Series
DRV Series, Heat Sink
Length (mm)
9
Width (mm)
9
Weight (g)
4 (Weight of 5Pcs)
Shipping Weight
0.02 kg
Shipping Dimensions
4 × 3 × 3 cm
See all specifications