
1 / 4 · Click to enlarge
AI Summary
A compact DFRobot breakout built around the BMP280 sensor, delivering barometric pressure and temperature readings over I2C at 3.3 to 5.5 VDC. Its small 18 by 11.2 mm footprint makes it easy to fit into weather, altitude and navigation builds.
Key Highlights
- BMP280 pressure and temperature sensing on one small breakout
- I2C communication keeps wiring simple with just four pins
- Wide 3.3 to 5.5 VDC input suits common logic supplies
- Measures 300 to 1100 hPa for weather and altitude work
- Temperature range of 0 to 65 degrees Celsius
- Compact 18 x 11.2 mm board with mounting hole
Ideal For
- Arduino makers building weather or altitude projects
- Students learning I2C sensor integration
- Electronics hobbyists adding pressure data to compact builds
- Robot and wearable developers needing a small sensor board
- Navigation experimenters combining pressure with other sensors
Buying Tip
Check that your project has a free I2C bus and a supply between 3.3 and 5.5 VDC before ordering, and plan how you will mount the board using its 13 mm mounting hole.
Elecvora expert review
Our verdict
The DFRobot Fermion BMP280 is a tidy, small breakout that gives Arduino projects straightforward pressure and temperature data over I2C. It is a sensible choice when space is tight and you want a simple sensor with a flexible voltage range.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Small 18 x 11.2 mm board suits compact builds
- I2C wiring keeps connections simple
- 3.3 to 5.5 VDC range covers common supplies
- Measures both pressure and temperature
Cons
- Temperature measurement is limited to 0 to 65 degrees Celsius
- Header soldering is required before use
- No cable is included beyond the 4-pin connector
Best for
Compact Arduino weather, altitude and navigation projects
Not ideal for
Applications needing temperature readings below 0 degrees Celsius
Specifications
| Operating Voltage (VDC) | 3.3 to 5.5 |
|---|---|
| Communication Mode | I2C |
| Pressure Range (MPa) | 300~1100hPA |
| Measuring Temperature (°C) | 0~65 |
| Mounting Hole Diameter (mm) | 13 |
| Length (mm) | 18 |
| Width (mm) | 11.2 |
| Shipping Weight | 0.02 kg |
| Shipping Dimensions | 6 × 4 × 2 cm |
What's in the box
- 1 x BMP280 digital pressure sensor module (V1.0)
- 1 x 2.54 mm single-row 4-pin connector
Frequently Asked Questions
What does the BMP280 module measure?
How do I connect it to a microcontroller?
What supply voltage does it need?
What is included with the sensor?
How large is the board?
How should I care for the module?
Overview
The DFRobot Fermion BMP280 is a breakout module that puts digital barometric pressure and temperature measurement into a very small package. It is built around the BMP280 sensor and communicates over I2C, so a microcontroller can read pressure and temperature with only a handful of connections. The board runs from 3.3 to 5.5 VDC, which covers the usual supply rails found in hobby electronics projects.
Because pressure changes with height, the module can also be used to estimate altitude and relative floor height. That makes it more than a weather sensor: it can support navigation experiments, indoor positioning work and altitude tracking when combined with other data sources.
Key Features
- Dual measurement: reads both barometric pressure and temperature from a single board.
- I2C interface: simple two-wire communication that keeps wiring tidy.
- Flexible voltage: operates from 3.3 to 5.5 VDC.
- Small footprint: 18 mm long and 11.2 mm wide for tight builds.
- Mounting hole: a 13 mm mounting hole diameter is provided for fixing the board.
- Lightweight shipping: the packed module weighs about 0.02 kg.
Specifications Explained
The pressure range of 300 to 1100 hPa covers typical surface-level atmospheric conditions, so the sensor can follow weather-related pressure shifts as well as changes caused by moving up or down in altitude. Temperature measurement spans 0 to 65 degrees Celsius, which is suitable for indoor and normal outdoor electronics use.
The 3.3 to 5.5 VDC operating voltage means the module can share a supply with many common development boards. I2C communication reduces the pin count, and the 18 x 11.2 mm board size helps when space inside an enclosure is limited. The 13 mm mounting hole diameter gives you a way to secure the board mechanically rather than leaving it loose.
Compatibility and Requirements
The module uses I2C, so your controller needs an I2C bus and a supply within the 3.3 to 5.5 VDC range. Arduino code control is supported, making it straightforward to integrate into Arduino-based projects. A 2.54 mm single-row 4-pin connector is included for the header connection.
Typical Uses
- Weather stations and environmental data logging
- Altitude and relative height estimation
- Navigation experiments that benefit from pressure data
- Student and maker projects learning I2C sensors
- Compact robotics and wearable builds
What's in the Box
- 1 x BMP280 digital pressure sensor module (V1.0)
- 1 x 2.54 mm single-row 4-pin connector
Quick specs
- Operating Voltage (VDC)
- 3.3 to 5.5
- Communication Mode
- I2C
- Pressure Range (MPa)
- 300~1100hPA
- Measuring Temperature (°C)
- 0~65
- Mounting Hole Diameter (mm)
- 13
- Length (mm)
- 18


















