Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

The DFRobot Fermion MEMS CO Gas Sensor Breakout detects carbon monoxide from 5 to 5000 ppm and outputs an analog voltage. Its compact 13x13 mm size and low power draw make it ideal for portable CO alarms and DIY monitoring projects.

Key Highlights

  • MEMS CO sensor with 5–5000 ppm detection range
  • Analog voltage output for easy microcontroller interfacing
  • Compact 13 x 13 mm breakout board
  • Low power consumption, max 20 mA at 3.3–5 V
  • Fast response and recovery, short preheating time
  • Rated life cycle of 5 years or more

Ideal For

  • Makers building DIY carbon monoxide alarms
  • Students learning about gas sensors and MEMS technology
  • Engineers prototyping portable air quality monitors
  • Hobbyists creating environmental data loggers
  • Educators demonstrating sensor integration

Buying Tip

Remember to remove the protective film before use and avoid exposing the sensor to silicone vapors, corrosive gases, or condensation to ensure accurate readings and long life.

Elecvora expert review

Our verdict

The DFRobot Fermion MEMS CO Gas Sensor Breakout offers a compact, low-power solution for qualitative CO detection, ideal for DIY alarms and educational projects. Its analog output and wide voltage range make it easy to integrate, though it is not intended for precise quantitative measurements or safety-critical systems.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Very small 13 x 13 mm footprint
  • Low power consumption (max 20 mA)
  • Wide detection range (5–5000 ppm)
  • Simple analog interface
  • Long life cycle (≥5 years)

Cons

  • Qualitative measurements only, not factory-calibrated
  • Requires careful handling to avoid contamination
  • Not for use in personal safety systems

Best for

DIY CO alarms and educational gas sensing projects

Not ideal for

Safety-critical or quantitative measurement applications

Specifications

Item TypeGas Sensor
Operating Voltage (V)3.3 to 5
Detecting Range5-5000ppm
Max. Operating Current (A)20
Signal OutputAnalog Voltage
Operating Temperature (°C)-10~50℃
Operating humidity15-90%RH (non-condensing)
Life Cycle≥5 years
Length (mm)13
Width (mm)13
Weight (g)1 (approx)
Shipping Weight0.012 kg
Shipping Dimensions6 × 6 × 3 cm

What's in the box

  • 1 x DFRobot Fermion MEMS Carbon Monoxide CO Gas Detection Sensor (Breakout, 5–5000 ppm)
  • 1 x 2.54 mm pitch header

Frequently Asked Questions

What is the detection range of this sensor?
The sensor can detect carbon monoxide concentrations from 5 ppm up to 5000 ppm.
What output does the sensor provide?
It provides an analog voltage output that varies with CO concentration, which can be read by a microcontroller's ADC.
What power supply does it require?
The module operates from 3.3 V to 5 V DC and draws a maximum of 20 mA.
Can I use this sensor for quantitative measurements?
This sensor is intended for qualitative measurements only. For quantitative measurements, consider a factory-calibrated electrochemical sensor.
What is included in the package?
The package includes one DFRobot Fermion MEMS CO Gas Sensor Breakout and one 2.54 mm pitch header.
How should I care for the sensor?
Remove the protective film before use, avoid exposure to silicone vapors, corrosive gases, condensation, and extreme environments, and preheat for at least 24 hours after extended storage.

Overview

The DFRobot Fermion MEMS CO Gas Sensor Breakout is a compact module designed to detect carbon monoxide (CO) concentrations between 5 and 5000 ppm. It uses micro electromechanical system (MEMS) technology to deliver high sensitivity, rapid response and recovery, and minimal heat generation in a very small footprint. The board measures just 13 x 13 mm and weighs approximately 1 gram, making it easy to embed in portable and space-constrained projects.

This sensor provides an analog voltage output that varies with CO concentration, so it can be read directly by most microcontrollers with an ADC input. It is intended for qualitative measurements—ideal for building carbon monoxide leak alarms, portable detectors, and educational or prototyping projects. For quantitative measurements, a factory-calibrated electrochemical sensor is recommended.

Key Features

  • MEMS technology: advanced micro-machined sensing element for reliable CO detection.
  • Wide detection range: responds to CO from 5 ppm up to 5000 ppm.
  • Analog output: simple voltage signal proportional to gas concentration.
  • Low power: operates from 3.3 to 5 V with a maximum current of 20 mA.
  • Compact size: 13 x 13 mm breakout board, approximately 1 g.
  • Long life: rated for at least 5 years in air.
  • Fast response: short preheating time and quick recovery.

Specifications Explained

Operating voltage (3.3–5 V): the module can be powered from common 3.3 V and 5 V logic supplies, making it compatible with a wide range of development boards. Detection range (5–5000 ppm): the sensor can register carbon monoxide from trace levels up to high concentrations, suitable for alarm and monitoring applications. Analog voltage output: the output voltage changes with CO concentration; you read it with an ADC and apply a calibration curve if needed. Maximum current (20 mA): low current draw helps preserve battery life in portable devices. Operating temperature (-10 to 50 °C) and humidity (15–90% RH, non-condensing): designed for indoor and sheltered environments; avoid condensation and extreme conditions. Life cycle (≥5 years): indicates long-term usability under normal conditions.

Compatibility and Requirements

The sensor requires a 3.3–5 V DC power supply and a microcontroller or ADC capable of reading an analog voltage. No specific libraries or drivers are needed—just connect power, ground, and the analog output to your ADC. The included 2.54 mm pitch header allows easy connection to breadboards or perfboards. Note that this sensor is for qualitative measurements; for precise quantitative readings, consider a factory-calibrated electrochemical sensor.

Typical Uses

  • Carbon monoxide leak alarms and safety prototypes
  • Portable CO detectors for indoor air quality checks
  • Educational projects and gas sensor experiments
  • Environmental monitoring in petrochemical, metallurgy, or mining contexts (qualitative)
  • DIY electronic nose projects with multiple MEMS sensors

What's in the Box

  • 1 x DFRobot Fermion MEMS Carbon Monoxide CO Gas Detection Sensor (Breakout, 5–5000 ppm)
  • 1 x 2.54 mm pitch header

Quick specs

Item Type
Gas Sensor
Operating Voltage (V)
3.3 to 5
Detecting Range
5-5000ppm
Max. Operating Current (A)
20
Signal Output
Analog Voltage
Operating Temperature (°C)
-10~50℃
See all specifications