Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

The DFRobot Fermion MiCS-2714 is a MEMS gas sensor breakout that measures hydrogen (1-1000ppm) and nitrogen dioxide (0.05-10ppm) with an analog output. Its 5V operation and low-power enable pin make it easy to integrate into Arduino-based gas detection projects.

Key Highlights

  • MEMS sensor detects H2 (1-1000ppm) and NO2 (0.05-10ppm)
  • Analog voltage output for simple microcontroller interfacing
  • 5V operation with power enable/disable pins for low power
  • Compact 12mm x 16mm board with 2mm mounting holes
  • Operating range 30-85°C and 5-95%RH (no condensation)
  • Life cycle over 2 years in air for long-term use

Ideal For

  • Arduino hobbyists building gas detection projects
  • Students learning about MEMS sensors and analog interfacing
  • Makers developing air quality monitoring devices
  • Engineers prototyping hydrogen leak detectors
  • Educators demonstrating sensor principles in workshops

Buying Tip

Remember to order a 5V power source and an ADC-equipped microcontroller; the board does not include headers or cables.

Elecvora expert review

Our verdict

The DFRobot Fermion MiCS-2714 offers a straightforward way to add hydrogen and nitrogen dioxide sensing to a project. Its analog output and low-power control make it flexible, though it requires careful power supply design and calibration for accurate results.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Dual-gas detection in a single compact board
  • Analog output simplifies interfacing with many microcontrollers
  • Power enable pin supports low-power duty-cycled operation
  • Wide operating temperature and humidity range
  • Long life cycle of over 2 years in air

Cons

  • Requires a regulated 5V supply within tight tolerance
  • No headers or connectors included, so soldering is needed
  • Measurement accuracy depends on calibration and environmental conditions

Best for

Makers and engineers prototyping gas detection or air quality monitoring systems.

Not ideal for

Those seeking a fully calibrated, plug-and-play gas detection instrument.

Specifications

Operating Voltage (V)4.9 to 5.1
Power Dissipation (W)0.45W
Signal OutputAnalog quantity
Measurement Range1 – 1000ppm(Hydrogen H2) ,0.05 – 10ppm(Nitrogen dioxide NO2 )
Operating Temperature (°C)30~85℃
Operating humidity5~95%RH (No condensation)
Storage Temperature (°C)-40~85℃
Life Cycle>2 years(in the air)
Mounting Hole Diameter (mm)Inner diameter 2mm/outer diameter 4mm
Circuit board size12mm×16mm
Shipping Weight0.006 kg
Shipping Dimensions6 × 5.5 × 2.5 cm

What's in the box

  • 1 x DFRobot Fermion MEMS Gas Sensor - MiCS-2714 (Breakout)

Frequently Asked Questions

What gases can this sensor detect?
It detects hydrogen (H2) in the range 1-1000ppm and nitrogen dioxide (NO2) in the range 0.05-10ppm.
What is the output type?
The sensor provides an analog voltage output that varies with gas concentration.
What power supply does it need?
It requires a regulated 5V supply between 4.9V and 5.1V. The board includes power enable/disable pins for low-power operation.
Is it compatible with Arduino?
Yes, it can be used with Arduino and other microcontrollers that have an analog input and a 5V supply.
What is included in the package?
The package contains one DFRobot Fermion MEMS Gas Sensor - MiCS-2714 (Breakout) board. Headers and cables are not included.
How should I care for the sensor?
Operate it within 30-85°C and 5-95%RH without condensation. Avoid exposing it to high concentrations of organic solvents or silicone vapors, which can affect sensitivity.

Overview

The DFRobot Fermion MiCS-2714 is a breakout board built around a MEMS gas sensor that responds to hydrogen (H2) and nitrogen dioxide (NO2). It outputs an analog voltage that varies with gas concentration, so you can read it with any microcontroller that has an ADC. The board is intended for prototyping and educational projects in gas detection, air quality monitoring, and safety equipment. Its small footprint and mounting holes make it easy to fix inside an enclosure or onto a custom carrier board.

Key Features

  • Dual-gas detection: measures H2 from 1 to 1000ppm and NO2 from 0.05 to 10ppm.
  • Analog output: provides a continuous voltage signal proportional to gas concentration.
  • Low-power control: dedicated power enable/disable pins let you switch the sensor off between readings.
  • Compact size: 12mm x 16mm circuit board with 2mm inner diameter mounting holes.
  • Wide operating conditions: works from 30°C to 85°C and 5% to 95% relative humidity (no condensation).
  • Long life: rated for more than 2 years in air.

Specifications Explained

Operating voltage (4.9-5.1V): the board expects a regulated 5V supply, so it pairs well with common 5V microcontrollers and USB power. Power dissipation (0.45W): indicates the sensor consumes about 90mA at 5V, which is typical for MEMS gas sensors and should be considered when sizing your power source. Analog output: the voltage changes with gas concentration; you will need an ADC with enough resolution to detect small changes, especially for the low NO2 range. Measurement ranges: the H2 range covers leak detection and general monitoring, while the NO2 range is suited to low-concentration environmental sensing. Operating temperature and humidity: the sensor is specified for 30-85°C and 5-95%RH without condensation, so avoid condensing environments. Life cycle: over 2 years in air gives reasonable longevity for continuous or intermittent use.

Compatibility and Requirements

The board requires a 5V supply within 4.9-5.1V and a microcontroller with an analog input to read the output. It is compatible with Arduino and similar boards that operate at 5V logic. Sample code with concentration conversion formulas is available from the manufacturer to help translate the analog reading into gas concentration. You will need to provide your own wiring, headers, and enclosure; the board is a bare breakout without connectors soldered.

Typical Uses

  • Gas leak detection prototypes for hydrogen systems.
  • Air environment detection and indoor air quality experiments.
  • Gas safety equipment development and testing.
  • Educational projects demonstrating MEMS gas sensing.
  • Integration into IoT nodes for remote monitoring.

What's in the Box

1 x DFRobot Fermion MEMS Gas Sensor - MiCS-2714 (Breakout).

Quick specs

Operating Voltage (V)
4.9 to 5.1
Power Dissipation (W)
0.45W
Signal Output
Analog quantity
Measurement Range
1 – 1000ppm(Hydrogen H2) ,0.05 – 10ppm(Nitrogen dioxide NO2 )
Operating Temperature (°C)
30~85℃
Operating humidity
5~95%RH (No condensation)
See all specifications