Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by DFRobot, this usb interface module is a good fit for makers, students and electronics hobbyists. Main specs: operating voltage (v) 5; response time(s) 4; connector type PH2.0-3P. Check that your power source supplies 5 before connecting it.

Key Highlights

  • Operating Voltage (V): 5
  • Response Time(s): 4
  • Connector Type: PH2.0-3P

Ideal For

  • Arduino, ESP32 and Raspberry Pi projects
  • School and college lab work
  • Prototypes and test rigs

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Operating Voltage (V)5
Response Time(s)4
Connector TypePH2.0-3P
No-Load Current (mA)75
Dimensions (L x W x H) mm42 * 32
Weight (g)10
Shipping Weight22 kg
Shipping Dimensions6 × 5 × 2 cm

Overview

The DFRobot Gravity Analog Signal Isolator, made by DFRobot, is listed in our usb interface module range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Operating Voltage (V): 5 (match this to your power supply; too high a voltage can damage the part)
  • Response Time(s): 4
  • Connector Type: PH2.0-3P (confirm your cable or board uses the same connector)
  • No-Load Current (mA): 75 (your supply must deliver at least this much current)
  • Dimensions (L x W x H) mm: 42 * 32 (measure your mounting space before ordering)
  • Weight (g): 10 (important for drones, RC models and anything you carry)
  • Shipping Weight: 22 kg (important for drones, RC models and anything you carry)
  • Shipping Dimensions: 6 × 5 × 2 cm (measure your mounting space before ordering)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

Signal isolators are used in industrial, medical, and other environments in which electrical isolation is essential for safety. Signal isolators can also be used to amplify signals, enable instruments to be added to an overburdened loop, or step down dangerous, high-voltage signals to safer levels. In many cases, electrical isolation is required to ensure reliable operation of the sensors. Some sensors, such as pH sensors and conductivity sensors, will interfere with each other and do not measure properly in the same container when they connect to the same power. To ensure the stable and reliable operation of the sensors with no interference, it is necessary to isolate the signal and the power. Gravity: Analog Signal Isolator is efficient in preventing electrical interference between sensors. This module has an onboard 5V isolation power which could directly supply to the sensor. Therefore, you do not need to prepare the external power, such an easy and practical! The connectors of wires are specially designed for DF Robot 3Pin analog sensor, plug and play, no need for soldering. The analog signal transmission ratio is 1:1, which contributes to a very small impact on the output signals of sensors when this module connects to the circuit. Furthermore, you do not need to change the code of the mainboard. This analog signal isolator is applicable to prevent interferences between sensors, such as a multi-parameter water quality monitoring system that needs to prevent interferences between water sensors. This product is almost compatible with all analog sensors produced by DFRobot. It could satisfy varied demands in situations that require electrical isolation


Useful link:

DFRobot Gravity Analog Signal Isolator tutorial.


Feature:

  1.  Remove earth loop errors which are caused by noise & signal interference.
  2.  Provide electrical (galvanic) isolation between the input and output circuits.
  3. Signal isolators can also be used to amplify signals
  4.  enable instruments to be added to an overburdened loop, or to step down dangerous, high-voltage signals to safer levels.
  5. Analog Error between Two Terminals: <± 20mV (Typ).
  6. Non-isolation Terminal (MCU Terminal). Supply Voltage: 5.0 ± 0.1V. Analog Output: 0 ~ 5.0V.
  7. Isolation Terminal (SEN Terminal). Output Voltage: 5.0 ± 0.2V. Analog Input: 0 ~ 5.0V.

Packages Includes:

1 x DFRobot Gravity Analog Signal Isolator.

Quick specs

Operating Voltage (V)
5
Response Time(s)
4
Connector Type
PH2.0-3P
No-Load Current (mA)
75
Dimensions (L x W x H) mm
42 * 32
Weight (g)
10
See all specifications