Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact Gravity-format CO2 sensor module based on the Sensirion SCD41, measuring 400 to 5000 ppm with temperature and humidity over I2C. It runs on 3.3V to 5V and averages under 4mA, making continuous air quality monitoring practical.

Key Highlights

  • Photoacoustic NDIR sensing with CO2, temperature and humidity in one module
  • Wide 400 to 5000 ppm CO2 measurement range for indoor and greenhouse air
  • I2C interface at address 0x62 with Gravity 4-pin cable included
  • 3.3V to 5V supply and under 4mA average current draw
  • Compact 32 x 27 x 8 mm board fits tight enclosures
  • On-chip temperature and humidity compensation for CO2 readings

Ideal For

  • Makers building indoor air quality monitors
  • Greenhouse growers tracking ambient CO2
  • Engineers prototyping demand-controlled ventilation
  • Educators teaching sensor and I2C projects
  • Developers adding CO2 data to Gravity-based builds

Buying Tip

Check that your controller's I2C bus is free at address 0x62 and that your cable route reaches the board's Gravity connector before mounting it in a sealed enclosure.

Elecvora expert review

Our verdict

A neatly packaged CO2 module that combines the SCD41 sensor with Gravity wiring, giving CO2, temperature and humidity over one I2C link. Its low current draw and small size make continuous monitoring builds straightforward.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Three measurements from a single module
  • Low average current under 4mA
  • Wide 3.3V to 5V supply range
  • Compact 32 x 27 x 8 mm board
  • Gravity cable included for quick connection

Cons

  • Fixed I2C address 0x62 limits multiple units per bus
  • Temperature channel response time of 120s slows settling
  • No enclosure or mounting hardware included

Best for

Continuous indoor and greenhouse CO2 monitoring projects

Not ideal for

Builds needing several CO2 sensors on one I2C bus without a multiplexer

Specifications

Power Supply Voltage (V)3.3V to 5V
Avg. Current Consumption<4mA
I2C Address0x62
Size (mm)32*27*8mm/1.26×1.06×0.31"
Measurement Range400 - 5000 ppm
Humidity Range0 to 95%RH
Operating Temperature (°C)-10 to 60℃
Response Time(s)120s (Temperature)
Shipping Weight0.013 kg
Shipping Dimensions6 × 6 × 3 cm

What's in the box

  • 1 x Gravity SCD41 Infrared CO2 Sensor
  • 1 x Gravity-4P I2C/UART Sensor Cable

Frequently Asked Questions

What does this sensor measure?
It measures CO2 concentration from 400 to 5000 ppm and also provides temperature and humidity readings.
How does it connect to a controller?
It uses I2C at address 0x62 and connects through the included Gravity-4P I2C/UART sensor cable.
What supply voltage does it need?
The module accepts 3.3V to 5V and draws under 4mA on average.
How large is the board?
The module measures 32 x 27 x 8 mm, so it fits small enclosures.
What is included with the sensor?
You receive one Gravity SCD41 Infrared CO2 Sensor and one Gravity-4P I2C/UART sensor cable.
What temperature and humidity conditions can it handle?
It operates from -10 to 60°C and across 0 to 95%RH.

Overview

The DFRobot Gravity SCD41 is a small sensor board for measuring carbon dioxide concentration in air. It is built around the Sensirion SCD41, a miniature sensor that uses the photoacoustic NDIR principle: pulsed infrared light is absorbed by CO2 molecules, producing a pressure wave that an on-board microphone detects, and the concentration is calculated from that signal. The module also includes a temperature and humidity sensor that compensates the CO2 reading and makes those values available as separate outputs.

The board follows the Gravity form factor and connects with the included 4-pin I2C/UART cable, so it works with Gravity-compatible controllers and any host that supports I2C at address 0x62.

Key Features

  • Three measurements in one module: CO2 concentration, temperature and humidity.
  • 400 to 5000 ppm range: covers typical indoor and greenhouse CO2 levels.
  • Low power: average current consumption below 4mA.
  • Flexible supply: operates from 3.3V to 5V.
  • Small footprint: 32 x 27 x 8 mm board.
  • Simple wiring: Gravity 4-pin I2C connector at address 0x62.

Specifications Explained

Measurement range (400 to 5000 ppm): the sensor reports CO2 from roughly outdoor background levels up to concentrations well above what is normally found in occupied rooms, so it can track both fresh-air baselines and poorly ventilated spaces.

Supply voltage (3.3V to 5V): the module can share the logic supply of common 3.3V boards or run from a 5V rail, which simplifies mixing it into existing builds.

Average current (under 4mA): low enough for continuously powered monitoring nodes without a heavy power budget.

Humidity (0 to 95%RH) and temperature (-10 to 60°C): the operating envelope covers normal indoor rooms and most greenhouse conditions.

Response time (120s, temperature): the temperature channel settles over a couple of minutes, so allow a short warm-up before logging stable values.

I2C address 0x62: a fixed address to set in your code; only one SCD41 module can sit on a bus at a time unless you use a multiplexer.

Compatibility and Requirements

The module needs a host with an I2C interface and a 3.3V or 5V supply. Connection is made through the supplied Gravity-4P I2C/UART sensor cable. Because the I2C address is 0x62, plan your bus so no other device uses the same address.

Typical Uses

  • Indoor CO2 concentration monitoring in homes, offices and classrooms
  • Ambient monitoring in greenhouses
  • Smart ventilation systems that react to CO2 levels
  • Educational and prototyping projects on air quality

What's in the Box

  • 1 x Gravity SCD41 Infrared CO2 Sensor
  • 1 x Gravity-4P I2C/UART sensor cable

Quick specs

Power Supply Voltage (V)
3.3V to 5V
Avg. Current Consumption
<4mA
I2C Address
0x62
Size (mm)
32*27*8mm/1.26×1.06×0.31"
Measurement Range
400 - 5000 ppm
Humidity Range
0 to 95%RH
See all specifications