
1 / 4 · Click to enlarge
AI Summary
A Gravity-format UV and ambient light sensor board built on the LTR390-UV-01, covering 280–430nm with digital output over I2C or UART. An onboard ADC and MCU deliver raw readings with up to 20-bit effective resolution at roughly 2.73mA.
Key Highlights
- LTR390-UV-01 sensor with UV response from 280nm to 430nm
- Digital output over I2C at address 0x1C or UART
- Onboard ADC and MCU handle signal conversion
- 13 to 20 bits effective resolution for fine light steps
- Programmable interrupt thresholds with upper and lower limits
- Compact 32mm × 27mm Gravity board running at 3.3V
Ideal For
- Makers building UV index or light-level data loggers
- Teachers running weather and light experiments
- Students learning I2C and UART sensor interfacing
- Engineers adding UV detection to outdoor monitoring devices
- Developers prototyping ambient light sensing on 3.3V boards
Buying Tip
Check that your controller runs a 3.3V logic supply and that address 0x1C is free on your I2C bus before wiring the module in.
Elecvora expert review
Our verdict
A tidy, well-integrated UV and light sensor board that removes the analogue design work and gives you digital readings over I2C or UART. It is a sensible pick for teaching, logging and prototype UV monitoring where a 3.3V supply is available.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Onboard ADC and MCU deliver digital output directly
- I2C and UART options in one board
- Wide 280–430nm UV response with ambient light sensing
- Up to 20-bit effective resolution and programmable interrupts
- Compact 32mm × 27mm Gravity footprint
Cons
- Specified for 3.3V operation, so 5V-only hosts need care
- Fixed I2C address 0x1C limits address conflicts on a shared bus
- UV readings are uncalibrated raw data, so absolute UV index work needs your own reference
Best for
Makers and educators who want plug-and-play UV and light data on a 3.3V controller
Not ideal for
Projects that need a factory-calibrated UV index reading out of the box
Specifications
| Operating Voltage (V) | 3.3 |
|---|---|
| Operating Current (mA) | 2.73 |
| MCU Type | LTR390-UV-01 |
| Communication Mode | I2C/UART |
| I2C Address | 0x1C |
| UV Response Wavelength | 280nm to 430nm |
| Output Type | digital output |
| Overall Dimension | 32mm×27mm/1.26×1.06" |
| Shipping Weight | 0.015 kg |
| Shipping Dimensions | 6 × 5 × 3 cm |
What's in the box
- 1 x DFRobot Gravity LTR390 UV Light Sensor (280nm to 430nm) with I2C and UART
Frequently Asked Questions
What does the LTR390-UV-01 sensor measure?
How do I connect the module to my controller?
What supply voltage does it need?
What resolution can I expect?
Can I trigger an action when light crosses a limit?
What is included with the sensor?
Overview
The DFRobot Gravity LTR390 UV Sensor brings UV and ambient light measurement to a small, connector-friendly board. At its centre sits the LTR390-UV-01, a sensor with a UV response spanning 280nm to 430nm. Rather than asking you to build an analogue front end, DFRobot paired the chip with an onboard ADC and MCU, so the board hands you finished digital values instead of raw voltages.
Readings leave the module over I2C at address 0x1C or over UART, which makes it easy to pair with common microcontrollers or to feed a serial data logger. The board measures 32mm × 27mm and runs from a 3.3V supply while drawing about 2.73mA.
Key Features
- UV plus ambient light sensing across a 280–430nm UV response range.
- Two digital interfaces: I2C at 0x1C or UART, selected to suit your project.
- Built-in conversion through an onboard ADC and MCU, giving a digital output.
- Fine resolution from 13 to 20 bits effective, useful when light levels change gradually.
- Interrupt function with programmable upper and lower thresholds.
- Gravity form factor in a 32mm × 27mm footprint.
Specifications Explained
The 280–430nm UV response defines what the sensor is tuned to see, covering the UV band rather than the full visible spectrum, so it suits UV monitoring tasks alongside general light readings.
Digital output matters for accuracy and simplicity: the onboard ADC and MCU convert the light signal before it reaches your controller, so your code reads a number rather than sampling an analogue pin. The 13 to 20 bits of effective resolution means small changes in illumination remain visible in the data.
I2C address 0x1C is fixed in the specifications, so plan your bus around it. The 3.3V operating voltage and 2.73mA current draw are modest, making the board easy to power in compact builds.
Compatibility and Requirements
The module is specified for a 3.3V supply and communicates over I2C or UART. Your host board needs a matching I2C bus or serial port, and the I2C address to use is 0x1C. The Gravity connector simplifies cabling to Gravity-compatible boards; otherwise, wire the pins according to the labels on the module.
Typical Uses
- UV intensity and UV index monitoring projects
- Ambient light measurement and light detection experiments
- Weather experiments for teaching and classroom demonstrations
- Outdoor UV detection setups and data loggers
What's in the Box
One DFRobot Gravity LTR390 UV Light Sensor (280nm to 430nm) with I2C and UART support.
Quick specs
- Operating Voltage (V)
- 3.3
- Operating Current (mA)
- 2.73
- MCU Type
- LTR390-UV-01
- Communication Mode
- I2C/UART
- I2C Address
- 0x1C
- UV Response Wavelength
- 280nm to 430nm


















