Skip to main content

Worldwide Shipping · Secure Payments

At a glance

Made by DFRobot, this df robot modules is a good fit for makers, students and electronics hobbyists. Main specs: interface type PH2.0-3P; item type Accessory; model no. / name Power Controller.

Key Highlights

  • Interface Type: PH2.0-3P
  • Item Type: Accessory
  • Model No. / Name: Power Controller

Ideal For

  • Arduino, ESP32 and Raspberry Pi projects
  • School and college lab work
  • Prototypes and test rigs

Buying Tip

Compare the pin layout and operating voltage with your circuit, and order a spare or two: small parts are easy to damage while soldering.

Specifications

Interface TypePH2.0-3P
Item TypeAccessory
Model No. / NamePower Controller
Operating Temperature (°C)-55 to 155
Switching frequency0-1
Length (mm)44
Width (mm)32
Bluetooth VersionSupports Bluetooth 5.1 dual mode function
Shipping Weight0.015 kg
Shipping Dimensions9 × 8 × 3 cm

Overview

The DFRobot Gravity MOSFET Power Controller, made by DFRobot, is listed in our df robot modules range and suits makers, students and electronics hobbyists. The notes below explain the main specifications and what to check before you order.

Specifications explained

  • Interface Type: PH2.0-3P (confirm your cable or board uses the same connector)
  • Item Type: Accessory
  • Model No. / Name: Power Controller
  • Operating Temperature (°C): -55 to 155
  • Switching frequency: 0-1 (make sure the rest of your system works at this frequency)
  • Length (mm): 44 (measure your mounting space before ordering)
  • Width (mm): 32 (measure your mounting space before ordering)
  • Bluetooth Version: Supports Bluetooth 5.1 dual mode function (check your phone or controller supports the same Bluetooth version for full range)

Before you order

Compare the specifications with your project or device, and check delivery times and return terms for your country in our help centre. Questions about this item? Email [email protected] with the product code.

In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the internal coil to pick-up contact. But for some MCU, like Intel Edison, Intel joule, lilypad, Raspberry Pi and other microcontroller with limited amount of current GPIO, it’s hard to drive one or more relays simultaneously. The MOSFET power controller is a module which can drive a large current device with limited current GPIO. It works as a MOSFET relay or MOSFET driver. When you give it a digital high-level signal (3.3~10V), MOSFET turns on, vice versa. Compare to the relay module, MOSFET power controller is compatible with Arduino, Raspberry Pi, Lattepanda and other Microcontroller, supports 3.3~10V logic power control. The VIN port supports 5~36V; 0~20A power input, if the current is over 10A, we recommend an external heat sink. And MOSFET supports quick ON-OFF switch, the switching frequency arrives 1KHz. That is a good point for robot control. The MOSFET power controller comes with a standard PH2.0-3P gravity interface. It makes the module compatible with the Arduino IO expansion shield. Plug and play, easy to use.

Useful link:

For more information refer to the tutorial

Features:

  1. VIN Operating Voltage: 5V-36V DC
  2. VIN Operating Current: 0A-20A (Suggest external heat sink when the current over 10A )
  3. Logic Operating Voltage: 3.3~10V DC
  4. Logic Control Signal: 3.3~10V DC

Package Includes:

1 x Gravity: MOSFET Power Controller

1 x Gravity Digital Sensor Cable

Quick specs

Interface Type
PH2.0-3P
Item Type
Accessory
Model No. / Name
Power Controller
Operating Temperature (°C)
-55 to 155
Switching frequency
0-1
Length (mm)
44
See all specifications