Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact DRV8825 breakout board that drives bipolar stepper motors from 8.2 to 42 VDC with up to 2.2 A peak and selectable microstepping down to 1/32-step. The included aluminum heat sink and adjustable current potentiometer make it easy to tune for your motor.

Key Highlights

  • 8.2 to 42 VDC motor supply with 2.5 to 5 V logic
  • Up to 2.2 A peak, 1.5 A continuous per phase
  • Six microstep modes from full-step to 1/32-step
  • Adjustable current limit via onboard potentiometer
  • Aluminum heat sink included for improved cooling
  • Compact 15 x 20 mm board weighing about 4 g

Ideal For

  • 3D printer builders replacing or upgrading axis drivers
  • CNC router and engraver hobbyists using bipolar steppers
  • Robotics and automation projects needing precise positioning
  • Makers building camera sliders and motion stages
  • Electronics learners working with step-and-direction control

Buying Tip

Set the current potentiometer for your motor's rated current before connecting a load, and fit the supplied heat sink if you plan to run near the top of the current range.

Elecvora expert review

Our verdict

A tidy, well-featured driver board that covers the common microstep settings and includes the heat sink many builds end up needing. It is a sensible choice for small bipolar steppers where current is set carefully.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Six microstep modes up to 1/32-step
  • Adjustable current limiting via potentiometer
  • Wide 8.2 to 42 VDC motor supply range
  • Logic works from 2.5 to 5 V
  • Heat sink included in the package

Cons

  • Requires a separate motor power supply
  • Current must be set manually for each motor
  • Continuous rating is 1.5 A per phase, so 2.2 A needs extra cooling

Best for

3D printers, small CNC machines and robotics using bipolar steppers

Not ideal for

High-current motors running continuously near 2.2 A without extra cooling

Specifications

Model SeriesDRV Series, Heat Sink
Voltage Rating (V)8.2 to 42VDC
Current Rating (A)1.5 to 2.2
Input Voltage (VDC)8.2 ~ 42
Logic Voltage (V)2.5 ~ 5
Max Current (A)2.2
Continuous Discharge Current (A)1.5 (per phase)
Length (mm)15
Width (mm)20
Weight (g)4
Shipping Weight0.05 kg
Shipping Dimensions4 × 4 × 4 cm

What's in the box

  • 1 x DRV8825 Stepper Motor Driver with Aluminum Heat Sink – Good Quality

Frequently Asked Questions

What voltage does the DRV8825 need?
The motor supply must be between 8.2 and 42 VDC, and the logic side needs 2.5 to 5 V. These are separate supplies, so plan for both in your build.
How much current can it deliver?
It is rated for 1.5 A continuous per phase and up to 2.2 A peak. The heat sink helps with cooling, but the current limit should be set to suit your motor.
Can it run a bipolar stepper motor?
Yes, it is designed for bipolar stepper motors and uses a step-and-direction interface. Wire each motor coil to the correct output pair.
What microstep settings are available?
The board supports full-step, 1/2, 1/4, 1/8, 1/16 and 1/32-step modes, selected with the microstep pins.
What is included with the driver?
The package contains one DRV8825 stepper motor driver board with an aluminum heat sink.
How do I set the current limit?
Use the onboard potentiometer to adjust the current limit, starting low and raising it gradually until it matches your motor's rating.

Overview

The DRV8825 is a stepper motor driver breakout board built around a bipolar microstepping driver IC. It is supplied with a clip-on aluminum heat sink and measures roughly 15 x 20 mm, so it fits into tight driver sockets on compact motion-control builds. Motor power is taken from a separate supply of 8.2 to 42 VDC, while the logic side works from 2.5 to 5 V, which lets it interface with common 3.3 V and 5 V controllers.

Control is deliberately simple: a step input, a direction input and the microstep selection pins. A small potentiometer sets the current limit, so you can match the driver to the motor you are using rather than running it at full output.

Key Features

  • Six microstep resolutions: full-step, 1/2, 1/4, 1/8, 1/16 and 1/32-step
  • Step and direction control interface for straightforward wiring
  • Adjustable current limiting through an onboard potentiometer
  • Up to 2.2 A peak and 1.5 A continuous per phase
  • Over-current, over-temperature and under-voltage protection
  • Four-layer, 2 oz copper PCB with an exposed ground pad under the IC
  • Aluminum heat sink included in the package

Specifications Explained

Voltage

The 8.2 to 42 VDC rating applies to the motor supply, not the logic supply. Running a stepper at a higher voltage than its rated coil voltage is normal practice because the driver chops the current, and it helps the motor reach higher step rates. Keep the motor supply within the stated range.

Current

Continuous current is 1.5 A per phase, with a 2.2 A maximum. The heat sink helps here, but the current limit should still be set with the potentiometer to suit your motor. Higher current settings produce more heat, so treat 2.2 A as a peak figure rather than a continuous target.

Microstepping

Selecting 1/32-step gives finer positioning and smoother motion at low speeds, while full-step and half-step modes are useful when you need more torque or simpler timing. The resolution is chosen with the microstep pins.

Logic Level

A logic range of 2.5 to 5 V means the board can be driven directly by 3.3 V and 5 V systems, with no external logic supply needed.

Compatibility and Requirements

The board is designed for bipolar stepper motors and requires a separate motor power supply within the 8.2 to 42 VDC range plus a logic supply of 2.5 to 5 V. Its pinout and interface follow the common carrier layout used for this driver family, which makes it a practical replacement in existing sockets. Current must be set for your specific motor before use.

Typical Uses

Typical applications include 3D printer motion axes, small CNC routers and engravers, camera sliders, robotic arms and other projects where a bipolar stepper needs accurate, repeatable positioning.

What's in the Box

  • 1 x DRV8825 Stepper Motor Driver with Aluminum Heat Sink – Good Quality

Quick specs

Model Series
DRV Series, Heat Sink
Voltage Rating (V)
8.2 to 42VDC
Current Rating (A)
1.5 to 2.2
Input Voltage (VDC)
8.2 ~ 42
Logic Voltage (V)
2.5 ~ 5
Max Current (A)
2.2
See all specifications