Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact 3-phase brushless motor driver board built on the TMC6300 IC, running from 2V to 11V with up to 2A peak drive. Six PWM inputs and built-in thermal and short-circuit protection make precise low-power BLDC control straightforward.

Key Highlights

  • TMC6300 driver IC for 3-phase BLDC and PMSM motors
  • Wide 2V to 11V supply range suits low-power battery systems
  • Up to 2A peak output, rated 1.4ARMS continuous
  • Six PWM inputs for full phase commutation control
  • Thermal shutdown and short-circuit protection built in
  • Breadboard-compatible layout with 1.8V regulated output

Ideal For

  • Makers prototyping low-voltage BLDC motor control on a breadboard
  • Robotics hobbyists building small actuator and joint drives
  • Engineering students learning field-oriented control with Arduino
  • Designers of compact battery-powered motion systems
  • Developers needing a driver with fault diagnostics and a 1.8V rail

Buying Tip

Check that your motor's rated current stays comfortably below the 1.4ARMS continuous figure and that your supply sits within 2V to 11V before ordering.

Elecvora expert review

Our verdict

A tidy, well-protected driver board for small three-phase motors, especially where supply voltage is limited. Its six PWM inputs and fault output give more control than simple plug-and-play drivers, at the cost of more wiring work.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Works from supplies as low as 2V
  • Separate high-side and low-side control for precise commutation
  • Thermal and short-circuit protection with diagnostic output
  • Onboard 1.8V regulator and breadboard-friendly layout

Cons

  • Current ceiling of 2A peak limits it to small motors
  • Requires the user to wire six PWM channels and motor phases
  • No motor or cables included in the box

Best for

Low-voltage BLDC and PMSM prototyping on breadboards and compact builds

Not ideal for

High-current or high-voltage motor applications

Specifications

Driver ICTMC6300
Voltage Range (V)2 to 11
Max Current (A)2A (1.4ARMS)
Protection FeaturesThermal shutdown, short circuit
Dimensions (L x W x H) mm50x50x21
Weight (g)17
Shipping Weight0.05 kg
Shipping Dimensions9 × 6 × 2 cm

What's in the box

  • 1 x SmartElex TMC6300 3 Phase Brushless Motor Driver

Frequently Asked Questions

What kind of motors can this board drive?
It is designed for three-phase brushless DC (BLDC) and permanent magnet synchronous (PMSM) motors within its voltage and current limits.
What supply voltage does it need?
The board accepts anything from 2V to 11V, so it suits low-voltage battery packs and bench supplies in that range.
How much current can it handle?
It is rated for a maximum of 2A, or 1.4ARMS continuous, so it is intended for small motors rather than high-power drives.
Does it work with Arduino field-oriented control?
Yes, it is compatible with the Arduino Simple Field Oriented Control library, which can be used to generate the commutation signals.
What is included with the board?
The package contains one SmartElex TMC6300 3 Phase Brushless Motor Driver board; motor, wiring and controller are not included.
How should I handle faults during operation?
The board includes thermal shutdown and short-circuit protection plus a diagnostic output, so monitor that line in firmware and cut power if a fault is reported.

Overview

The SmartElex TMC6300 3-Phase Brushless Motor Driver is a small, breadboard-friendly board that puts the TMC6300 driver IC to work in your own projects. It is built to drive three-phase brushless DC (BLDC) and permanent magnet synchronous (PMSM) motors, using separate high-side and low-side control so you can shape commutation precisely rather than relying on a fixed internal sequence.

With a supply range of 2V to 11V and a maximum drive current of 2A (1.4ARMS), the board targets low-power motion: small gimbals, miniature pumps, compact robotic joints and lightweight propulsion setups. The layout measures roughly 50 x 50 x 21 mm and weighs only 17 g, so it adds little bulk to a build.

Key Features

  • TMC6300 driver IC for three-phase BLDC and PMSM motor control.
  • Six PWM inputs enabling independent high-side and low-side switching for accurate commutation.
  • 2V to 11V operating range that works with low-voltage battery packs and bench supplies.
  • 2A peak, 1.4ARMS output for modest loads.
  • Protection circuitry including thermal shutdown and short-circuit detection.
  • Diagnostic output for fault indication to your host controller.
  • Regulated 1.8V output for low-power microcontrollers.
  • Breadboard-compatible footprint for quick prototyping.

Specifications Explained

The voltage range is the headline figure here. A 2V minimum means the board can start working from supplies that would be too low for many drivers, which is useful in battery-powered designs where headroom is tight. The 11V ceiling keeps it firmly in low-voltage territory, so plan your motor and pack accordingly.

Current handling is rated at 2A maximum with 1.4ARMS continuous. In practice this suits small motors that draw modest current; if your motor's rated current sits near or above the peak figure, choose a different driver. The separate high-side and low-side control is what allows fine commutation timing, and it is the reason six PWM channels are exposed.

On the safety side, thermal shutdown and short-circuit protection reduce the risk of damage during wiring mistakes or stalled conditions, while the diagnostic output lets your firmware react to a fault instead of running blind. The onboard 1.8V regulator can power a small microcontroller, simplifying wiring in compact builds.

Compatibility and Requirements

The board is compatible with the Arduino Simple Field Oriented Control library, which is helpful if you want to move beyond basic six-step commutation. You will need a host microcontroller capable of generating the PWM signals and reading the diagnostic line, plus a suitable power supply within the 2V to 11V window. Motor phase leads and control wiring must be connected by the user.

Typical Uses

  • Small robotics joints and actuator prototypes.
  • Battery-powered gimbal and stabilisation projects.
  • Miniature pump and fan drive experiments.
  • Teaching and learning field-oriented control with Arduino.
  • Rapid breadboard prototyping of three-phase motor control.

What's in the Box

One SmartElex TMC6300 3 Phase Brushless Motor Driver board.

Quick specs

Driver IC
TMC6300
Voltage Range (V)
2 to 11
Max Current (A)
2A (1.4ARMS)
Protection Features
Thermal shutdown, short circuit
Dimensions (L x W x H) mm
50x50x21
Weight (g)
17
See all specifications