Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A laboratory-grade analog conductivity kit for high-salinity liquids, measuring 10 to 100 mS/cm with a BNC probe and a 3–5 V signal board. AC excitation and single-point calibration with automatic buffer recognition keep readings stable and setup simple.

Key Highlights

  • Laboratory-grade K=10 probe covers 10 to 100 mS/cm conductivity
  • Wide 3 to 5 V input works with 5 V and 3.3 V boards
  • AC excitation reduces polarization and extends probe life
  • Gravity and BNC connectors for solder-free plug-and-play wiring
  • Library supports single-point calibration and automatic buffer recognition
  • Integrated temperature compensation algorithm in the software library

Ideal For

  • Marine aquaculture and fisheries operators monitoring water quality
  • Marine aquarium keepers checking salinity and conductivity
  • Laboratory technicians measuring concentrated brine
  • Makers building Arduino or Raspberry Pi conductivity projects
  • Educators demonstrating EC measurement in high-salinity liquids

Buying Tip

Confirm your controller has an analog input that can read the 0 to 3.2 V output, and keep the supplied 12.88 mS/cm buffer solution for calibration before measuring samples.

Elecvora expert review

Our verdict

A focused, well-equipped kit for anyone measuring high-conductivity liquids, with the probe, board, cable and calibration solution supplied together. The AC excitation and library-based calibration make it approachable without sacrificing the range needed for seawater and brine.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Range up to 100 mS/cm suits seawater and concentrated brine
  • Wide 3 to 5 V input works with 5 V and 3.3 V boards
  • AC excitation reduces polarization and supports probe life
  • Gravity and BNC connectors avoid soldering
  • Buffer solution and mounting hardware included

Cons

  • Accuracy of ±5% F.S. limits precision-critical work
  • Operating range capped at 0 to 40°C
  • Requires a controller with an analog input and library setup

Best for

High-salinity water monitoring in mariculture, marine aquariums and brine measurement

Not ideal for

Low-conductivity or drinking-water measurements below 10 mS/cm

Specifications

Operating Voltage (VDC)3 to 5
Output Voltage0~3.2V
Probe ConnectorBNC
Signal ConnectorPH2.0-3Pin
Measurement Accuracy±5% F.S.
Probe TypeLaboratory Grade
Detection range10~100ms/cm
Operating Temperature (°C)0~40℃
Board Size (mm)42mm x 32mm/1.65in x 1.26in
Shipping Weight0.324 kg
Shipping Dimensions24 × 14 × 7 cm

What's in the box

  • 1 x Electrical Conductivity Probe (K=10, Laboratory Grade)
  • 1 x Signal Conversion Board
  • 4 x Standard Buffer Solution 12.88 mS/cm
  • 1 x Gravity Analog Sensor Cable
  • 2 x Waterproof Gasket
  • 1 x Screw Cap for BNC Connector
  • 4 x M3 x 10 Nylon Pillar

Frequently Asked Questions

What liquids is this sensor intended for?
It is designed for high-conductivity liquids such as seawater and concentrated brine, with a detection range of 10 to 100 mS/cm.
Which boards can I use it with?
The 3 to 5 VDC input and 0 to 3.2 V output make it compatible with 5 V and 3.3 V mainboards, including Arduino and Raspberry Pi.
Do I need to solder anything?
No. The probe uses a BNC connector and the board uses a PH2.0-3Pin Gravity connector, so the supplied cable connects without soldering.
How is calibration handled?
The software library uses a single-point calibration method and can automatically identify a standard buffer solution. Four 12.88 mS/cm buffer solutions are included.
What is the operating temperature range?
The sensor is specified for operation between 0 and 40°C.
Is temperature compensation included?
Yes. The software library integrates a temperature compensation algorithm to support consistent readings.

Overview

The DFRobot Gravity Lab EC Sensor Meter K10 is an analog conductivity measurement kit designed for liquids where salt concentration is high. Seawater, concentrated brine and similar solutions push past the range of ordinary conductivity probes, so this version uses a laboratory-grade probe with a K=10 cell constant and a detection range of 10 to 100 mS/cm.

The kit pairs that probe with a compact signal conversion board measuring 42 mm x 32 mm. The board accepts 3 to 5 VDC and outputs 0 to 3.2 V, which makes it usable with both 5 V and 3.3 V mainboards. A Gravity PH2.0-3Pin connector handles the signal side, while the probe attaches through a BNC connector, so no soldering is required.

Key Features

  • AC excitation source: driving the probe with an AC signal reduces polarization effects, which supports accuracy and helps prolong probe life.
  • Single-point calibration: the software library uses a single-point method and can automatically identify a standard buffer solution.
  • Temperature compensation: a compensation algorithm is included in the library to support consistent readings.
  • Plug-and-play connectors: Gravity and BNC connectors remove the need for soldering during assembly.
  • Uniform form factor: consistent sizing and connectors simplify mechanical design and enclosure planning.

Specifications Explained

Detection range and accuracy

The 10 to 100 mS/cm range targets high-conductivity liquids rather than drinking water or low-salinity samples. Measurement accuracy is stated as ±5% F.S., meaning a percentage of full scale, so plan your readings with that tolerance in mind.

Voltage and output

With a 3 to 5 VDC input and a 0 to 3.2 V output, the board fits common logic levels. Check that your controller's analog input can accept the output span before connecting.

Probe and connectors

The probe is laboratory grade and connects over BNC. The signal board links to your controller through a PH2.0-3Pin Gravity connector. Operating temperature is specified at 0 to 40°C.

Compatibility and Requirements

The wide input voltage makes the board compatible with 5 V and 3.3 V main control boards, including Arduino and Raspberry Pi. You will need a controller with an analog input, the supplied Gravity analog sensor cable, and access to the DFRobot software library for calibration and temperature compensation. A standard buffer solution is included for calibration.

Typical Uses

  • Water quality monitoring in mariculture, including marine fisheries
  • Marine aquarium salinity and conductivity checks
  • Concentrated brine measurement in laboratory or process work
  • Educational and prototype projects involving high-conductivity liquids

What's in the Box

  • 1 x Electrical Conductivity Probe (K=10, Laboratory Grade)
  • 1 x Signal Conversion Board
  • 4 x Standard Buffer Solution 12.88 mS/cm
  • 1 x Gravity Analog Sensor Cable
  • 2 x Waterproof Gasket
  • 1 x Screw Cap for BNC Connector
  • 4 x M3 x 10 Nylon Pillar

Quick specs

Operating Voltage (VDC)
3 to 5
Output Voltage
0~3.2V
Probe Connector
BNC
Signal Connector
PH2.0-3Pin
Measurement Accuracy
±5% F.S.
Probe Type
Laboratory Grade
See all specifications