Skip to main content

Worldwide Shipping · Secure Payments

AI Summary

A compact 8-channel breakout that safely converts logic levels between a 1.2V-3.6V side and a 1.65V-5.5V side with no direction control needed. It handles I2C, SPI, UART and OneWire signals at up to 60Mbps push-pull while drawing only about 30uA.

Key Highlights

  • Eight bidirectional channels translate automatically with no direction control pin
  • A side tracks 1.2V-3.6V; B side tracks 1.65V-5.5V supply rails
  • Up to 60Mbps push-pull and 2Mbps open-drain conversion speed
  • Low 30uA working current suits battery-powered and portable builds
  • Compact 15.5 x 26mm board with M2.0 mounting holes at 22mm PCD
  • Works across I2C, UART, SPI and OneWire level conversion

Ideal For

  • Makers connecting 5V sensors to 3.3V microcontrollers
  • Students learning mixed-voltage interfacing
  • Engineers prototyping I2C, SPI, UART or OneWire buses
  • Robotics builders mixing modules from different logic families
  • Battery-powered projects needing a low-current interface

Buying Tip

Confirm your two logic voltages first and check that the lower one sits on VCCA and the higher on VCCB before wiring anything up.

Elecvora expert review

Our verdict

A tidy, low-current translator that removes the guesswork from mixed-voltage wiring and covers both fast push-pull and open-drain buses. It is a sensible part to keep on the bench for anyone who regularly mixes 3.3V and 5V modules.

AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.

Pros

  • Eight channels in a small 15.5 x 26mm footprint
  • Automatic bidirectional translation with no direction pin
  • Covers both 60Mbps push-pull and 2Mbps open-drain use
  • Very low 30uA working current
  • M2.0 mounting holes simplify installation

Cons

  • Requires both supply rails from your own system
  • VCCA must not exceed VCCB, which limits some rail pairings
  • Headers need soldering before breadboard use

Best for

Makers and engineers bridging 3.3V and 5V logic in I2C, SPI, UART or OneWire projects

Not ideal for

Projects that need the board to generate or regulate its own supply voltages

Specifications

Model No. / NameLevel Translator
Working Current (uA)30uA
Conversionspeed push-pull 60Mbps(MAX)open-drain 2Mbps(MAX)
Operating Temperature (°C)-30℃~75℃
Size (mm)15.5*26mm/0.61×1.02 inches
Mounting Hole PCD (mm)22mm
Mounting Hole Diameter (mm)M2.0
Additional Specs.VCCA Voltage Range: 1.2V-3.6V, VCCB Voltage Range: 1.65V-5.5V
Shipping Weight0.007 kg
Shipping Dimensions8 × 5 × 1 cm

What's in the box

  • 1 x 8-Bit Level Translator
  • 2 x 2.54mm black single-row 10-pin headers

Frequently Asked Questions

Do I need a direction pin to use this translator?
No. Translation is bidirectional and automatic, so each channel handles signals moving either way without a control pin.
Which voltages go to VCCA and VCCB?
VCCA accepts 1.2V to 3.6V and VCCB accepts 1.65V to 5.5V. VCCA must be less than or equal to VCCB.
What signal speeds can it handle?
Up to 60Mbps in push-pull applications and up to 2Mbps in open-drain applications.
Can I use it for I2C?
Yes, it is intended for level conversion of I2C, UART, SPI and OneWire communication.
Does the board supply power to my sensors?
No. It only translates logic levels; both VCCA and VCCB must come from your own system.
What is included with the module?
One 8-Bit Level Translator board and two 2.54mm black single-row 10-pin headers.

Overview

Mixing modules from different logic families often ends in a sensor that behaves erratically or a controller pin that takes damage. The DFRobot Fermion 8-Bit Level Translator solves that by placing a dedicated bidirectional translator between two voltage domains. The A port follows VCCA, which accepts 1.2V to 3.6V, and the B port follows VCCB, which accepts 1.65V to 5.5V. VCCA must stay at or below VCCB. With those two rails set, the board moves signals cleanly between 1.2V, 1.8V, 2.5V, 3.3V and 5V nodes.

Because translation is automatic and bidirectional, there is no direction pin to drive and no firmware change to make. The board is small enough for tight builds and simple enough for a first prototype.

Key Features

  • Eight channels, one board: translate a full byte of signals at once, or use only the lines you need.
  • Automatic direction sensing: no GPIO spent on direction control.
  • Fast conversion: up to 60Mbps in push-pull applications and up to 2Mbps in open-drain applications.
  • Low current draw: approximately 30uA working current.
  • Wide temperature range: rated for -30C to 75C operation.
  • Easy mounting: 15.5 x 26mm outline with M2.0 holes on a 22mm pitch circle.

Specifications Explained

Two supply rails: VCCA sets the low-voltage side and VCCB sets the high-voltage side. Keep VCCA less than or equal to VCCB, and match each rail to the logic level of the device connected to that side.

Conversion speed: the 60Mbps push-pull figure covers fast digital lines such as SPI clocks, while the 2Mbps open-drain figure covers bus styles like I2C. Choose the figure that matches your signal type rather than the headline number.

Working current: at roughly 30uA the translator adds very little load, which matters in battery-powered projects.

Thermal range: operation from -30C to 75C covers indoor benches, most enclosures and typical field use within that window.

Compatibility and Requirements

The board translates between any nodes within its rail ranges, including 1.2V, 1.8V, 2.5V, 3.3V and 5V logic. Both supply voltages must be provided by your own system; the board does not generate either rail. Keep VCCA at or below VCCB. The module is suited to level conversion for I2C, UART, SPI and OneWire communication.

Typical Uses

  • Connecting 5V sensors and peripherals to a 3.3V microcontroller.
  • Bridging a 1.8V module to a 3.3V or 5V bus.
  • Prototyping mixed-voltage I2C or SPI chains on a breadboard.
  • Adding a safe interface between legacy 5V gear and modern low-voltage boards.

What's in the Box

  • 1 x 8-Bit Level Translator
  • 2 x 2.54mm black single-row 10-pin headers

Quick specs

Model No. / Name
Level Translator
Working Current (uA)
30uA
Conversion
speed push-pull 60Mbps(MAX)open-drain 2Mbps(MAX)
Operating Temperature (°C)
-30℃~75℃
Size (mm)
15.5*26mm/0.61×1.02 inches
Mounting Hole PCD (mm)
22mm
See all specifications