
1 / 3 · Click to enlarge
AI Summary
A two-channel brushed DC motor driver for RC vehicles and medium robots, delivering 12A continuous and 25A peaks per channel. Regenerative drive, DIP-switch mode selection and built-in protection make it a dependable, compact choice.
Key Highlights
- Dual-channel driver, 12A continuous and 25A peak per channel
- Synchronous regenerative drive recharges the battery on braking
- DIP switches select analog, R/C or serial control modes
- Thermal, overcurrent and polarity protection built in
- 1A switching BEC powers a receiver or microcontroller
- Ultrasonic 32kHz switching for quiet operation
Ideal For
- RC car and boat builders wanting dual-motor control
- Differential-drive robot builders
- Combat robot teams working up to 30lb
- Hobbyists using brushed DC motors with an RC receiver
Buying Tip
Check that your motors' continuous draw stays within 12A per channel and that your pack voltage sits inside the 18-24V range before ordering.
Elecvora expert review
Our verdict
A well-rounded dual driver for RC and medium robot builds, with regenerative braking and protection that make it forgiving during testing. The DIP-switch setup keeps configuration simple and repeatable.
AI-assisted analysis based on the manufacturer's specifications. Not a hands-on lab test.
Pros
- Regenerative drive improves efficiency and braking feel
- Thermal, overcurrent and polarity protection
- Four control modes selected by DIP switches
- Compact 41 g board with a 1A switching BEC
Cons
- No onboard cooling fan, so sustained high current needs airflow
- Not an Arduino shield; requires wired connections
- Cheap AC adapters alone are not recommended
Best for
RC vehicles and differential-drive robots using brushed DC motors
Not ideal for
Builders needing an Arduino shield form factor or fan-cooled high-current operation
Specifications
| Item Type | Sabertooth Dual Motor Driver |
|---|---|
| Operating Voltage (VDC) | 18 ~ 24 |
| Peak Current (A) | 25 |
| Cooling Fan | No |
| No. of Channels | 2 |
| Operating Mode | Analog, R/C, Simplified serial, Packetized serial |
| Battery Protect. Mode (Y/N) | Yes |
| Over-Current Protection (A) | Yes |
| Thermal Protection (Y/N) | Yes |
| LED Indicator | Yes |
| Continuous Discharge Current (A) | 12 |
| Arduino Shield (Y/N) | No- can be used with Wire connection |
| Polarity Protection (Y/N) | Yes |
| Dimensions (L x W x H) mm | 59 x 48 x 15 |
| Others | Ultra-sonic switching frequency |
| Weight (g) | 41 |
| Shipping Weight | 0.043 kg |
| Shipping Dimensions | 6 × 6 × 4 cm |
What's in the box
- 1 x Sabertooth Dual 12A Motor Driver for R/C
- 1 x Mounting nut and bolt set
- Quick start guide
Frequently Asked Questions
How many motors can this driver control?
What voltage does it need?
How much current can each channel handle?
Which control modes are available?
Can it power my receiver?
What is included in the package?
Overview
The Dimension Engineering Sabertooth Dual 12A for R/C is a compact two-channel motor driver made for radio-controlled vehicles and medium-powered robots. It controls two brushed DC motors directly, with 12A continuous and 25A peak current available on each channel. Because it uses synchronous regenerative drive, energy is fed back to the battery whenever the vehicle slows or reverses, and fast stops and direction changes stay smooth.
Key Features
- Dual motor control: two channels in a 59 x 48 x 15 mm board weighing 41 g.
- Regenerative topology: braking and reversing return energy to the pack.
- Four operating modes: analog, R/C, simplified serial and packetized serial, chosen with onboard DIP switches.
- Protection suite: thermal, overcurrent and polarity protection plus battery protection mode.
- 1A switching BEC: supplies a receiver, microcontroller or a servo or two.
- Quiet switching: ultrasonic 32kHz frequency keeps motor noise low.
Specifications Explained
The 18-24V operating range suits common robot and RC battery packs. Continuous current of 12A per channel covers most medium vehicles, while 25A peaks handle brief loads such as acceleration or a short stall. Overcurrent and thermal protection cut in before the driver is damaged, so an accidental stall is less likely to end a run. Lithium protection mode lets the driver work safely with lithium packs. The LED indicator gives a quick visual check of status, and the absence of a cooling fan keeps the board slim and simple to mount.
Compatibility and Requirements
The driver works with brushed DC motors and supports analog, R/C and serial control, so it pairs with a standard RC receiver or a microcontroller over a wired connection. It is not an Arduino shield, but it can be used with a wire connection. A suitable battery or a DC supply with a battery in parallel is recommended; cheap AC adapters alone are not advised.
Typical Uses
Differential-drive robots, radio-controlled tanks, cars and boats, and combat robots up to 30lb are all natural fits. The regenerative drive and quick reversing also suit vehicles that need nimble, responsive handling.
What's in the Box
- 1 x Sabertooth Dual 12A Motor Driver for R/C
- 1 x Mounting nut and bolt set
- Quick start guide
Quick specs
- Item Type
- Sabertooth Dual Motor Driver
- Operating Voltage (VDC)
- 18 ~ 24
- Peak Current (A)
- 25
- Cooling Fan
- No
- No. of Channels
- 2
- Operating Mode
- Analog, R/C, Simplified serial, Packetized serial





















